Regarding the indicator lamps, Has been detected, Power

3M™ Digital Projector X30N/X35N

Troubleshooting

Regarding the indicator lamps

When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table.

POWER	LAMP	TEMP	Description
indicator	indicator	indicator	Description
indicator	indicator	indicator

Lighting	Turned	Turned	The projector is in a standby state.
In Orange	off	off	Please refer to the section “Power on/off”.
Blinking	Turned	Turned	The projector is warming up.
In Green	off	off	Please wait.
Lighting	Turned	Turned	The projector is in an on state.
In Green	off	off	Ordinary operations may be performed.
Blinking	Turned	Turned	The projector is cooling down.
In Orange	off	off	Please wait.
			The projector is cooling down. A certain error
Blinking	(discre-	(discre-	has been detected.
In Red	tionary)	tionary)	Please wait until POWER indicator finishes blinking,
In Red	tionary)	tionary)	and then perform the proper measure using the item
			and then perform the proper measure using the item
			descriptions below.
			The lamp does not light, and there is a possibility
			that interior portion has become heated.
			Please turn the power off, and allow the projector to
Blinking			cool down at least 20 minutes. After the projector has
Blinking			sufficiently cooled down, please make confirmation of
In Red	Lighting	Turned	sufficiently cooled down, please make confirmation of
In Red			the following items, and then turn the power on again.
or			the following items, and then turn the power on again.
or	In Red	off	• Is there blockage of the air passage aperture?
Lighting	In Red	off	• Is there blockage of the air passage aperture?
Lighting			• Is the air filter dirty?
In Red			• Is the air filter dirty?
In Red			• Does the peripheral temperature exceed 35°C?
			• Does the peripheral temperature exceed 35°C?
			If the same indication is displayed after the remedy,
			please change the lamp referring to the section
			“Replacing the lamp”.
			The lamp door has not been properly fixed.
Blinking			Please turn the power off, and allow the projector to
Blinking			cool down at least 45 minutes. After the projector has
In Red	Blinking	Turned	cool down at least 45 minutes. After the projector has
In Red			sufficiently cooled down, please make confirmation of
or			sufficiently cooled down, please make confirmation of
or	In Red	off	the attachment state of the lamp door. After performing
Lighting	In Red	off	the attachment state of the lamp door. After performing
Lighting			any needed maintenance, turn the power on again.
In Red			any needed maintenance, turn the power on again.
In Red			If the same indication is displayed after the remedy,
			If the same indication is displayed after the remedy,
			please contact your dealer or service company.
			The cooling fan is not operating.
Blinking			Please turn the power off, and allow the projector to
Blinking			cool down at least 20 minutes. After the projector has
In Red	Turned	Blinking	cool down at least 20 minutes. After the projector has
In Red			sufficiently cooled down, please make confirmation
or			sufficiently cooled down, please make confirmation
or	off	In Red	that no foreign matter has become caught in the fan,
Lighting	off	In Red	that no foreign matter has become caught in the fan,
Lighting			etc., and then turn the power on again.
In Red			etc., and then turn the power on again.
In Red			If the same indication is displayed after the remedy,
			If the same indication is displayed after the remedy,
			please contact your dealer or service company.

(Continued on next page)	69
© 3M 2009. All Rights Reserved.

Regarding the indicator lamps

POWER

LAMP

TEMP

indicator

The projector is in a standby state.

In Orange

The projector is warming up.

The projector is in an on state.

The projector is cooling down.

The projector is cooling down. A certain error

has been detected.

that interior portion has become heated.

The lamp door has not been properly fixed.

The cooling fan is not operating.