3M S10C manual Main Menu

Page 23

Multifunctional Settings (continued)

MAIN Menu

With the MAIN menu, the items shown in the table below can be performed.

Perform each operation in accordance with the instructions in the table below.

MENU

MAIN

KEYSTONE

+0

PICTURE-1

BRIGHT

+0

PICTURE-2

CONTRAST

+0

INPUT

ASPECT

4:3

AUTO

WHISPER

NORMAL

SCREEN

MIRROR

NORMAL

OPTION

LANGUAGE

ENGLISH

 

[Language]

 

: SELECT

 

 

Item

KEYSTONE

BRIGHT

CONTRAST

ASPECT

WHISPER

MIRROR

LANGUAGE

RESET

Description

Adjust the Keystone (Vertical) Distortion:

Upper in the data Lower in the data

The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well.

When the V:INVERT or the H&V:INVERT is selected under the MIRROR item, if the projector screen is inclined or if the projector is angled downward, this function may not work correctly.

When the WIDE is selected under the ASPECT item of the MAIN menu, this adjustment is ignored.

When the zoom adjustment is set to the TELE side, this correction may be excessive. This function should be used with zoom set to WIDE whenever possible.

Adjust Brightness: Light Dark

Adjust Contrast: Strong Weak

Select an Aspect Ratio

At a RGB input:

4:3 16:9 15:9 32:15

At a RGB input, selecting an aspect ratio may display the message “SYNC IS

OUT OF RANGE”. In this case, please select one of other aspect ratios.

At a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input:

4:3 16:9 WIDE ZOOM

At a COMPONENT VIDEO input of 16:9 Hi-Vision of 1125i(1035i/1080i)/750p, only 16:9 can be selected.

When the 4:3 is selected under the SCREEN TYPE item of the OPTION menu, WIDE and ZOOM cannot be selected.

Select the Whisper Mode:

NORMAL WHISPER

When the WHISPER is selected, acoustic noise and screen brightness are reduced.

Select a Mirror Status:

NORMAL H:INVERT V:INVERT H&V:INVERT

Select a Menu Language:

 

 

 

 

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

NORSK

NEDERLANDS

 

日本語

PORTUGUÊS

中文

 

SVENSKA

SUOMI

POLSKI

 

Reset the MAIN Menu Items:

 

 

 

 

 

Selecting the EXECUTE performs this function.

 

 

 

EXECUTE

CANCEL

 

 

 

 

 

The items of the MAIN menu are collectively returned to the initial setting. Note that the items WHISPER and LANGUAGE are not reset.

23

Image 23
Contents S10C Multimedia Projector Contents Preparation Projector FeaturesAttaching The Base Part NamesProjector Happened ProjectorRemote Control Arrangement Setting UpTwisting the elevator feet by hand Adjusting The Projectors ElevatorAdjust the height of the projector by As necessary, you can also finelyConnecting Your Devices Connecting to a DVD/VCR player Connecting Power Supply Putting Batteries Remote ControlRemove Battery cover Close Battery coverOperating The Remote Control Press the button of the projector Power ON/OFFTurning On The Power Or the remote controlUse the focus ring to focus the picture Selecting An Input SignalSelecting a RGB signal Press the RGB button of the remote Use the zoom ring to adjust the screen SizeSwitch the power switch to O OFF Turning Off The PowerProjector or the remote control Temporarily Muting The Sound Adjusting The VolumeOperating Press the Position button Adjusting The PositionUse Buttons to adjust Position Correcting Keystone Distortions Using The Automatic Adjustment FeaturePress the Magnify on button Using The Magnify FeatureUse Buttons to adjust the zoom Level Freezing The ScreenTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu MY Memory Load/Save a SettingReset the PICTURE-1 Menu Items Picture 1 MenuSize PhasePicture 2 Menu Position3D-YCS Input MenuVideo Frame LockS2-ASPECT Input MenuVideo NR InformationSearch AdjustAuto Menu Message Screen MenuStart UP Lamp Time Option MenuScreen Type Lamp Insert the new lamp, and tighten Replacing The LampUnscrew the 2 screws, and slowly Pick up the lamp by the handlesReplace the air filter and the filter cover Reset the filter timerAir Filter Caring For The Air FilterReplacing The Air Filter Caring For The Lens Caring For The Cabinet And Remote ControlOther Care Caring For The Inside Of The ProjectorRelated Messages TroubleshootingRelated Messages Power Lamp Temp Description Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceVideo Input Ports SpecificationsSpecification RGB Input Ports Audio PortsNot Included with Basic Packet How to OrderPart Number DN00571 QR58731