3M S10C Replacing The Lamp, Unscrew the 2 screws, and slowly, Pick up the lamp by the handles

Page 33

Lamp (continued)

Replacing The Lamp

WARNINGPlease carefully read the “Product Safety Guide”.

NOTE • Do not reset the lamp timer without replacing the lamp.

When you replace the lamp, please replace also the air filter. The air filter may be attached when you buy a replacement lamp for this projector. Please ask your dealer.

If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. If the projector is mounted on the ceiling, or if the lamp has broken, do not try to clean the projector or replace the lamp yourself.

1

Turn off the projector, and unplug the power cord. Allow the lamp

 

bulb to cool for at least 45 minutes.

 

 

2

Contact your local dealer to prepare a new lamp. Tell the dealer

 

your lamp type number. If the projector is mounted on the ceiling,

or if the lamp has broken, also ask the dealer to replace the lamp.

In the case of replacement by yourself,

After making sure that the projector

3 has cooled adequately, slowly flip over the projector, so that the bottom is facing up.

4 Unscrew the screw of the lamp door, then slide and take the lamp door up.

Lamp door

Screw

5

Unscrew the 2 screws, and slowly

 

pick up the lamp by the handles.

 

 

 

Insert the new lamp, and tighten the 2

6

 

screws firmly to lock it in place.

 

 

Handles

Screws

7

8

Slide the lamp door into place until it locks into position.

Slowly turn the projector so that the top is facing up.

Turn on the projector, and reset the lamp timer. When the lamp has

9 been replaced after the message of “THE POWER WILL TURN OFF AFTER 0hr.” is displayed, complete the following operation within 10 minutes of switching power on.

(1)While the projector running, press the MENU button to open the menu.

(2)Choose the “OPTION” on the menu using the / button, then press the button or ENTER button.

(3)Choose the “LAMP TIME” using the / button, then press and hold the button of projector or the RESET button of remote control for 3 seconds.

(4)Choose the “RESET” using the button.

33

Image 33
Contents S10C Multimedia Projector Contents Preparation Projector FeaturesPart Names ProjectorAttaching The Base Happened ProjectorRemote Control Arrangement Setting UpAdjust the height of the projector by Adjusting The Projectors ElevatorAs necessary, you can also finely Twisting the elevator feet by handConnecting Your Devices Connecting to a DVD/VCR player Connecting Power Supply Remove Battery cover Remote ControlClose Battery cover Putting BatteriesOperating The Remote Control Turning On The Power Power ON/OFFOr the remote control Press the button of the projectorSelecting a RGB signal Press the RGB button of the remote Selecting An Input SignalUse the zoom ring to adjust the screen Size Use the focus ring to focus the pictureTurning Off The Power Projector or the remote controlSwitch the power switch to O OFF Adjusting The Volume OperatingTemporarily Muting The Sound Adjusting The Position Use Buttons to adjust PositionPress the Position button Correcting Keystone Distortions Using The Automatic Adjustment FeatureUse Buttons to adjust the zoom Level Using The Magnify FeatureFreezing The Screen Press the Magnify on buttonSignal Searching Selecting The Aspect RatioTemporarily Blanking The Screen Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu Reset the PICTURE-1 Menu Items Load/Save a SettingPicture 1 Menu MY MemoryPicture 2 Menu PhasePosition SizeVideo Input MenuFrame Lock 3D-YCSVideo NR Input MenuInformation S2-ASPECTAdjust Auto MenuSearch Screen Menu Start UPMessage Option Menu Screen TypeLamp Time Lamp Unscrew the 2 screws, and slowly Replacing The LampPick up the lamp by the handles Insert the new lamp, and tightenAir Filter Reset the filter timerCaring For The Air Filter Replace the air filter and the filter coverReplacing The Air Filter Other Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingRelated Messages Power Lamp Temp Description Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceSpecification SpecificationsRGB Input Ports Audio Ports Video Input PortsHow to Order Part NumberNot Included with Basic Packet DN00571 QR58731