3M S10C manual Regarding The Indicator Lamps, Power Lamp Temp Description

Page 39

Troubleshooting (continued)

Regarding The Indicator Lamps

ATTENTION • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “” (power OFF) side of the main power switch, and wait at least 45 minutes. After the unit has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Lighting and flashing of the power indicator, the lamp indicator, and the temp indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company.

power

lamp

temp

Description

indicator

indicator

indicator

 

 

 

 

 

Lighting in

Turned off

Turned off

The unit is in a standby state. Please refer to the “Power

orange

ON/OFF” section of this manual.

 

 

 

 

 

 

Flashing in

Turned off

Turned off

The unit is warming up. Please wait.

green

 

 

 

 

 

 

 

Lighting in

Turned off

Turned off

The unit is in an ON state. Ordinary operations may be

green

performed.

 

 

 

 

 

 

Flashing in

Turned off

Turned off

The unit is cooling down. Please wait.

orange

 

 

 

 

 

 

 

 

 

 

The unit is cooling down. A certain error has been detected.

Blinking in

-

-

Wait until the power indicator has finished flashing, and then

red

perform the proper response measure using the item

 

 

 

 

 

descriptions below as reference.

 

 

 

 

 

 

 

The projector lamp has not been properly fixed (attached),

 

 

 

the projector lamp does not light, and/or there is a possibility

 

 

 

that the interior portion has become heated. Turn the power

Lighting or

 

 

OFF and wait at least 20 minutes. After the unit has sufficiently

Lighting in

 

cooled down, please make confirmation of the following items,

blinking in

Turned off

red

and then turn the power ON again. If the same indication is

red

 

displayed, please change the lamp.

 

 

 

 

 

• Is there blockage of the air passage aperture?

 

 

 

• Is the air filter is dirty?

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

 

Lighting or

 

 

The lamp cover has not been properly fixed (attached). Turn

Blinking in

 

the power OFF and wait at least 45 minutes. After the unit has

blinking in

Turned off

sufficiently cooled down, please make confirmation of the

red

red

 

attachment state of the lamp and lamp cover, and then turn

 

 

 

 

 

the power ON again.

 

 

 

 

39

Image 39
Contents S10C Multimedia Projector Contents Preparation Projector FeaturesPart Names ProjectorAttaching The Base Happened ProjectorRemote Control Arrangement Setting UpTwisting the elevator feet by hand Adjusting The Projectors ElevatorAdjust the height of the projector by As necessary, you can also finelyConnecting Your Devices Connecting to a DVD/VCR player Connecting Power Supply Putting Batteries Remote ControlRemove Battery cover Close Battery coverOperating The Remote Control Press the button of the projector Power ON/OFFTurning On The Power Or the remote controlUse the focus ring to focus the picture Selecting An Input SignalSelecting a RGB signal Press the RGB button of the remote Use the zoom ring to adjust the screen SizeTurning Off The Power Projector or the remote controlSwitch the power switch to O OFF Adjusting The Volume OperatingTemporarily Muting The Sound Adjusting The Position Use Buttons to adjust PositionPress the Position button Correcting Keystone Distortions Using The Automatic Adjustment FeaturePress the Magnify on button Using The Magnify FeatureUse Buttons to adjust the zoom Level Freezing The ScreenSignal Searching Selecting The Aspect RatioTemporarily Blanking The Screen Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu MY Memory Load/Save a SettingReset the PICTURE-1 Menu Items Picture 1 MenuSize PhasePicture 2 Menu Position3D-YCS Input MenuVideo Frame LockS2-ASPECT Input MenuVideo NR InformationAdjust Auto MenuSearch Screen Menu Start UPMessage Option Menu Screen TypeLamp Time Lamp Insert the new lamp, and tighten Replacing The LampUnscrew the 2 screws, and slowly Pick up the lamp by the handlesReplace the air filter and the filter cover Reset the filter timerAir Filter Caring For The Air FilterReplacing The Air Filter Caring For The Lens Caring For The Cabinet And Remote ControlOther Care Caring For The Inside Of The ProjectorRelated Messages TroubleshootingRelated Messages Power Lamp Temp Description Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceVideo Input Ports SpecificationsSpecification RGB Input Ports Audio PortsHow to Order Part NumberNot Included with Basic Packet DN00571 QR58731