3M S10C manual Option Menu, Screen Type, Lamp Time

Page 31

Multifunctional Settings (continued)

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

MENU

MAIN

VOLUME

16

PICTURE-1

SCREEN TYPE

4:3

PICTURE-2

LAMP TIME

1234h

INPUT

FILTER TIME

21h

AUTO

RESET

 

SCREEN

 

 

OPTION

 

 

: SELECT

Item

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

VOLUME

Adjust Volume: High

 

Low

 

 

 

 

 

 

 

 

 

 

Select the Screen Type:

 

 

 

 

 

 

4:3

16:9

 

16:9

16-9

SCREEN TYPE

• Please select the screen type used and the picture position in case of 16:9.

 

This selection is used as basic information for a suitable display. This function

 

should be performed before other picture adjustment.

 

 

 

 

 

 

To begin the operation of this item, please press the

button of the

 

projector or the RESET button of the remote control for 3 seconds.

 

Reset the Lamp Timer:

 

 

 

 

 

 

Selecting the RESET performs this function.

 

 

 

RESET

CANCEL

 

 

 

 

 

The numerical value of four digits shown on this menu is the projector use time since the last RESET operation of this item. The value is reset to 0 at the

LAMP TIME

same time the RESET is selected.

The value of this function is used to display the message of “CHANGE THE LAMP”. So this function must be performed only immediately after replacing the lamp.

Do not perform this function unless you have replaced the lamp. Perform this function every time the lamp is replaced. Incorrect performing of this function causes incorrect operation of the message function.

Please see to the section “Lamp” about replacing the lamp.

To begin the operation of this item, please press the button of the projector or the RESET button of the remote control for 3 seconds.

Reset the Filter Timer:

Selecting the RESET performs this function.

RESET

CANCEL

The numerical value of four digits shown on this menu is the projector use time since the last RESET operation of this item. The value is reset to 0 at the same time the RESET is selected.

FILTER TIME • The value of this function is used to display the message of “CLEAN THE AIR FILTER”. So this function must be performed only immediately after cleaning or replacing the air filter.

Do not perform this function unless you have cleaned or replaced the air filter. Perform this function every time the air filter is cleaned or replaced. Incorrect performing of this function causes incorrect operation of the message function.

Please see to the section “Air Filter” about cleaning and replacing the air filter.

 

Reset the OPTION Menu Items:

 

Selecting the EXECUTE performs this function.

RESET

EXECUTE

CANCEL

 

• The SCREEN TYPE item is returned to the initial setting. Note that the items

 

VOLUME, LAMP TIME and FILTER TIME are not reset.

31

Image 31
Contents S10C Multimedia Projector Contents Preparation Projector FeaturesProjector Part NamesAttaching The Base Happened ProjectorRemote Control Arrangement Setting UpTwisting the elevator feet by hand Adjusting The Projectors ElevatorAdjust the height of the projector by As necessary, you can also finelyConnecting Your Devices Connecting to a DVD/VCR player Connecting Power Supply Putting Batteries Remote ControlRemove Battery cover Close Battery coverOperating The Remote Control Press the button of the projector Power ON/OFFTurning On The Power Or the remote controlUse the focus ring to focus the picture Selecting An Input SignalSelecting a RGB signal Press the RGB button of the remote Use the zoom ring to adjust the screen SizeProjector or the remote control Turning Off The PowerSwitch the power switch to O OFF Operating Adjusting The VolumeTemporarily Muting The Sound Use Buttons to adjust Position Adjusting The PositionPress the Position button Correcting Keystone Distortions Using The Automatic Adjustment FeaturePress the Magnify on button Using The Magnify FeatureUse Buttons to adjust the zoom Level Freezing The ScreenSelecting The Aspect Ratio Signal SearchingTemporarily Blanking The Screen Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu MY Memory Load/Save a SettingReset the PICTURE-1 Menu Items Picture 1 MenuSize PhasePicture 2 Menu Position3D-YCS Input MenuVideo Frame LockS2-ASPECT Input MenuVideo NR InformationAuto Menu AdjustSearch Start UP Screen MenuMessage Screen Type Option MenuLamp Time Lamp Insert the new lamp, and tighten Replacing The LampUnscrew the 2 screws, and slowly Pick up the lamp by the handlesReplace the air filter and the filter cover Reset the filter timerAir Filter Caring For The Air FilterReplacing The Air Filter Caring For The Lens Caring For The Cabinet And Remote ControlOther Care Caring For The Inside Of The ProjectorRelated Messages TroubleshootingRelated Messages Power Lamp Temp Description Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceVideo Input Ports SpecificationsSpecification RGB Input Ports Audio PortsPart Number How to OrderNot Included with Basic Packet DN00571 QR58731