3M S10C manual Phenomena That May Easily Be Mistaken For Machine Defects

Page 41

Troubleshooting (continued)

Phenomena That May Easily Be Mistaken For Machine Defects

WARNINGPlease carefully read the “Product Safety Guide”.

Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur.

NOTE • Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

Before requesting repair, please check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Phenomenon

Cases not involving a machine defect,

Reference

and Items to be confirmed

pages

 

 

 

 

 

The main power source is not ON.

 

 

Turn on the main power.

11,14

 

 

 

The electrical power cord is not plugged in.

 

 

Power does not

Correctly connect the power cord.

 

 

 

come ON.

The main power source has been interrupted during operation,

 

 

such as by a power outage (blackout), etc.

 

 

Be sure to press the “” (power OFF) side of the main power switch,

14

 

and leave this OFF for at least 20 minutes. After the unit has

 

 

sufficiently cooled down, turn ON the power source.

 

 

 

 

Neither sounds

The input changeover settings are mismatched.

15

Select the input signal, and correct the settings.

nor pictures are

 

 

 

No signal is being inputted.

 

outputted.

10

 

Correctly connect the connection cables.

 

 

The electrical wiring to this unit is not correctly connected.

10

 

Correctly connect the connection cables.

Pictures are

 

 

 

The volume setting has been set at (or adjusted to) an

 

displayed,

17

extremely low level.

but no sounds

Adjust the VOLUME setting to a higher level.

 

are heard.

 

 

 

 

The MUTE mode is the current setting.

17

 

Press the MUTE button to release (change) the MUTE mode setting.

 

 

 

 

 

 

The electrical wiring to this unit is not correctly connected.

10

 

Correctly connect the connection cables.

Sounds are

 

 

 

The brightness setting has been set at (or adjusted to) an

 

heard,

23

extremely low level.

but no pictures

Adjust the BRIGHT setting to a brighter level.

 

are displayed.

 

 

 

 

The lens cap has not been removed.

4,14

 

Remove the lens cap.

 

 

 

 

 

Colors have a

Color settings are not correctly adjusted.

 

faded- out

 

Perform picture adjustments by changing the COLOR BAL R,

24

appearance, or

COLOR BAL G, COLOR BAL B, COLOR, and/or the TINT settings,

Color tone is

 

etc.

 

poor.

 

 

 

 

 

 

41

Image 41
Contents S10C Multimedia Projector Contents Preparation Projector FeaturesAttaching The Base Part NamesProjector Happened ProjectorRemote Control Arrangement Setting UpAdjust the height of the projector by Adjusting The Projectors ElevatorAs necessary, you can also finely Twisting the elevator feet by handConnecting Your Devices Connecting to a DVD/VCR player Connecting Power Supply Remove Battery cover Remote ControlClose Battery cover Putting BatteriesOperating The Remote Control Turning On The Power Power ON/OFFOr the remote control Press the button of the projectorSelecting a RGB signal Press the RGB button of the remote Selecting An Input SignalUse the zoom ring to adjust the screen Size Use the focus ring to focus the pictureSwitch the power switch to O OFF Turning Off The PowerProjector or the remote control Temporarily Muting The Sound Adjusting The VolumeOperating Press the Position button Adjusting The PositionUse Buttons to adjust Position Correcting Keystone Distortions Using The Automatic Adjustment FeatureUse Buttons to adjust the zoom Level Using The Magnify FeatureFreezing The Screen Press the Magnify on buttonTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu Reset the PICTURE-1 Menu Items Load/Save a SettingPicture 1 Menu MY MemoryPicture 2 Menu PhasePosition SizeVideo Input MenuFrame Lock 3D-YCSVideo NR Input MenuInformation S2-ASPECTSearch AdjustAuto Menu Message Screen MenuStart UP Lamp Time Option MenuScreen Type Lamp Unscrew the 2 screws, and slowly Replacing The LampPick up the lamp by the handles Insert the new lamp, and tightenAir Filter Reset the filter timerCaring For The Air Filter Replace the air filter and the filter coverReplacing The Air Filter Other Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingRelated Messages Power Lamp Temp Description Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceSpecification SpecificationsRGB Input Ports Audio Ports Video Input PortsNot Included with Basic Packet How to OrderPart Number DN00571 QR58731