Mitsubishi technical manual Mitsubishi 9800A Series UPS, Transportation and Installation

Page 34

MITSUBISHI	9800A SERIES UPS	Page Number:
ELECTRIC	OWNERS / TECHNICAL MANUAL	3-1

3.0INSTALLATION AND OPERATION

3.1Transportation and Installation

TABLE 3.1 How to transport and install the system

Transportation	Installation

Transport unit with forklift.	Using the pre drilled holes (4 - 24) in the
Carry with overhead crane using	UPS channel base, anchor the unit using
eyebolts provided.	appropriate hardware. (Not provided)

Note : Do not transport in a horizontal position. Cabinets must be maintained upright within +/- 15° of the vertical during handling.

3.2Installation Procedure

A)Note the load tolerance of the floor Refer to Table 3.2 for list of UPS weights.

TABLE 3.2 List of UPS weights

UPS Capacity (kVA)	100		150	225		300		375	500	750
Weight (lb.)	2100		2820	3310		4990		5250	6930	9655

B) Minimum clearance required for ventilation
Right side	25 mm (not required when sidecars are used)
Left side	25 mm (not required when sidecars are used)
Back side	0.0 mm
Top side	600 mm (for air flow)
C) Space requirement for routine maintenance
Allow for the following space at the time of installation.
Front	1000 mm 100kVA, 150kVA, 225kVA
	1075 mm 300kVA, 375kVA, 500kVA, 750kVA
Sides	0.0 mm
Rear	0.0 mm

MITSUBISHI ELECTRIC 9800A SERIES UPS

Image 34

Contents For parallel operation possible model only ALN-H0776Preface Table of Contents List of Tables List of Figures External I/F circuit PCB IOAU-04How to use this Manual Important Safety Instructions Retain These Instructions IntroductionMitsubishi Electric 9800A Series UPS General Mitsubishi Electric 9800A Series UPS Overview Mccb Rectifier Single Line Diagram Battery Operation CPM CUPS Parts Location 500kVA DUPS Parts Location 750kVA External contact signal terminal IOAU-04 Mitsubishi Electric 9800A Series UPS Specifications AC Output BatteryEnvironmental Rating of Contactors and Fuses Operator Controls and Indicators 540VLED Display Load on inverter Load on Inverter green Battery operation Battery OP. yellowLoad on bypass Load on Bypass green Menu Liquid Crystal DisplayStart/Stop screen Figure Start/Stop screen Measurement Menu FigureSetup Menu Figure Input Power Failure 11 Main screenFault Indication Figure 13 Main screen Fault indicationExternal Signal Terminal Block TN1TN2 CB2 AXOutput Contacts for external alarm annunciation 16 Control Wiring for External ContactsTerminals 5 to 6 Battery Temp. High contact input IN3 Input Contacts for remote access of UPSTerminals 3 to 4 Remote Inverter Stop input terminal IN2 Terminals 7 to 8 Power Demand Command contact input IN4 External communication connectorMitsubishi 9800A Series UPS Transportation and InstallationInstallation Procedure Minimum clearance required for ventilationProcedure for Cable Connections External Battery SupplyElectric Owners / Technical Manual Mitsubishi 9800A Series UPS Procedure for Cable Connections for Parallel System Recommended Cable Sizes Crimp Type Compression Lug NumberUPS module BN,BPUPS module Input UPS module CabinetInput Cabinet Bypass Output Input A50,B50,C50 A40,B40,C40 External signal terminal IOAU-04 TN2 DC circuit breaker Input Input Cabinet UPS module Wall mounted DC breaker Bypass Battery AC Output Floor mounted DC breaker Input cabinet UPS module Auxiliary Rectifier Cabinet RYER-E Critical Load Cabinet UPS-1 AC Output Critical Load CabinetIOAU-04 UPS-2 AC OutputUPS-1 IOAU-04 TN2 UPS-2 UPS-n*1Start-up of UPS Shut-down Procedure Number B Shut-down ProcedureBypass Operation Procedure UPSNumber MMS Start-up Procedure Start-up of UPS-1UPS Fault Response to UPS FailureBattery Parts ReplacementUPS Component Parts Fault Codes Contact Mitsubishi Electric Automation, Inc. atMitsubishi Igbt Fault a Inverter Voltage Activated Mitsubishi 9800A Series UPS Mitsubishi Electric Automation Inc 847