Meridian Audio D-ILA 1080MF2 operation manual Control Panel

Page 10

Controls and Features (continued)

Control Panel

1

2

3

4

5

1[TEMP] Indicator

	6
STAND BY
LAMP TEMP OPERATE	7
	7
	8

MENUEXIT

9

ENTER

p

PRESET

HIDE q

7[OPERATE] Indicator

Blinking : Indicates that temperature inside this unit is ab- normally high. (☞ Pages 11, 33)

Light on: When this unit is in operation (during projec- tion). (☞ Page 20)

2[LAMP] Indicator

Light on: Indicates that lamp has been used for more

than 1900 hours. (☞ Pages 11, 28)

Blinking : Indicates that lamp usage time (about 2000 hours) is exceeded. Replace the lamp. (☞ Pages 11, 28, 33)

3[MENU] Button

Press this button to display the menu. Pressing this but- ton when the menu is displayed clears the menu. (☞ Pages 23, 24)

4Cursor [5/∞/2/3] Buttons

Use these buttons when adjusting the menu items. (☞ Pages 23, 24)

5[PRESET] Button

Use this button to reset the values to factory settings when the “Gamma”, “Color temp.”, “Mask” or “Picture shift” item in the menu is selected.

6[STAND BY] Indicator

Light on: When in the standby mode. (☞ Page 11)

Blinking : When in the cool down mode. (☞ Page 11)

8[OPERATE] Button

When this unit is in the standby mode, pressing this but- ton for more than 1 second will turn this unit on and cause the [OPERATE] indicator to light up.

Press it for 1 second or more again to switch the unit to the cool down mode, which will automatically switch to the standby mode after about 90 seconds. (☞ Page 20)

●The [OPERATE] button will not work within approxi- mately 1 minute after the light source has been turned on. Start operation only after 1 minute’s time.

9[EXIT] Button

Press this button to return to the previous hierarchical menu (for example, to return from submenu to main menu). Pressing this button when the menu is displayed will clear the menu. (☞ Pages 23, 24)

p[ENTER] Button

Press this button to show the next hierarchical menu (for example, to enter submenu from main menu). It is also used when “ENTER” is displayed against a selection item on the menu screen. (☞ Pages 23, 24)

q[HIDE] Button

Use this button to temporarily clear the video image. Press again to resume. (☞ Page 21)

10

Image 10

Contents ILA 1080MF2 Machine Noise Information Germany only About the installation placeFCC Information U.S.A. only About burning-in of the D-ILA deviceDo not allow any unqualified person to install the unit Power cordHow To Replace The Fuse Do not cut off the main plug from this equipmentStandard for gauging replacement time of components Contents AccessoriesControls and Features Front Side/Top Surface/Left SideRear Side/Right Side/Bottom Surface Sync OUT Terminal RS-232C Terminal D-sub 9 Pin Connector PanelService Terminal DVI Terminal DVI-D 24 PinControl Panel Indicator Display on the Control Panel Remote Control Open the back cover Loading Batteries into the Remote ControlPrecautions for Using Batteries Load the batteriesPrecaution for Usage Installing the ProjectorInstallation Environment Adjusting the InclinationPrecautions for Ceiling-mount Projector and Screen InstallationMounting this Unit Screen Installation Screen Size and Projection Distance When reflecting off a screen Effective Range of Remote Control Unit When directing remote control unit toward this unit Right Side of this unit Connecting to Various DevicesConnecting to Devices Control from external deviceConnecting the Power Cord supplied When using this unit, remove the lens capAdjusting zoom screen size Basic Operation ProceduresTurning on the power Adjusting focusHiding the image temporarily Turning off the powerPull out the power plug from the power outlet Press HideAdjustments and Settings Using Menus Menu StructureButton Function This Unit Remote Control Unit Menu Operation ButtonsPress 5/ ∞ to select a main menu item and Enter Press the Menu buttonTo confirm Set up Menu Menu ConfigurationImage adjust Menu Options MenuProject image onto the screen Press 5/∞ to select Set up, followed by pressingScreen Masking Press the Menu buttonPicture Shift Setting Press 5/∞ to select Options, followed by press Ing EnterReplacing the Lamp About Lamp ReplacementLight-source Lamp and Lamp Usage Time Insert the new lamp unit until it is fully Loosen the screws on the lamp unit and lift up the handlePull out the lamp unit Tighten the screws of the lamp unit Close the handleTo ensure the lamp time has been reset Resetting Lamp TimeInsert plug into the power outlet ExitCleaning and Replacing the Filter What to do when these messages are displayed Message Cause DetailsPlease follow the procedures below About warning indicatorsIndicator Actions to be taken upon warning indicationsTroubleshooting Pin Arrangement Pin No Signal NameTerminal Description RS-232C TerminalRS-232C External Control Operation mode Only Asking command is possible External control command tableSpecial parameters Specifications Bottom Dimensions Unit mm TopFront SideMF2MIman v0.90ß