Meridian Audio D-ILA 1080MF2 operation manual Remote Control

Page 12

Controls and Features (continued)

Remote Control

1

5[MENU] Button

Press this button to display the menu. Pressing this but- ton when the menu is displayed clears the menu. (Pages 23, 24)

2

3

4

5

6

7

ON OPERATE OFF

FOCUS LIGHT TEST

MENUEXIT

ENTER

PRESETHIDE

 

6 Cursor [5//2/3] Buttons

8

Use these buttons when adjusting the menu items.

 

(Pages 23, 24)

9

7 [PRESET] Button

 

p

Use this button to reset the values to factory settings when

the “Gamma”, “Color temp.”, “Mask” or “Picture shift” item

 

q

in the menu is selected.

 

 

8 [OPERATE OFF] Button

 

When this unit is in operation (projecting), press it for 1

 

second or more to switch to the cool down mode, which

w

will automatically switch to the standby mode after about

 

90 seconds. (Page 21)

 

The [OPERATE OFF] button will not work within ap-

 

proximately 1 minute after the light source has been

 

turned on. Start operation only after 1 minute’s time.

 

9 [TEST] Button

 

Press this when adjusting focus, screen size or picture

 

quality. Press the button to switch to the test pattern im-

 

age for adjustment.

 

Alter the test pattern with the [TEST] button.

 

Press the [EXIT] button to return to the original image.

 

p [EXIT] Button

 

Press this button to return to the previous hierarchical

 

menu (for example, to return from submenu to main

 

menu). Pressing this button when the menu is displayed

 

will clear the menu. (Pages 23, 24)

1Remote Control’s Signal Transmitter

(Page 17)

2[OPERATE ON] Button

When this unit is in the standby mode, pressing the but- ton for more than 1 second will turn this unit on and cause the [OPERATE] indicator to light up. (Page 20)

3[LIGHT] Button

Lights up illumination (light) of the remote control buttons for about 10 seconds.

4[FOCUS] Button

Use this button to adjust focus of the projected image. Press the button to switch to the image mode for focus adjustment. Adjust focus using the focus ring on this unit. Press the [EXIT] button to return to the original image.

q[ENTER] Button

Press this button to show the next hierarchical menu (for example, to enter submenu from main menu). It is also used when “ENTER” is displayed against a selection item on the menu screen. (Pages 23, 24)

w[HIDE] Button

Press this button to temporarily clear the video image. Press again to resume. (Page 21)

12

Image 12
Contents ILA 1080MF2 About the installation place FCC Information U.S.A. onlyMachine Noise Information Germany only About burning-in of the D-ILA deviceDo not allow any unqualified person to install the unit Power cordHow To Replace The Fuse Do not cut off the main plug from this equipmentStandard for gauging replacement time of components Contents AccessoriesControls and Features Front Side/Top Surface/Left SideRear Side/Right Side/Bottom Surface Connector Panel Service TerminalSync OUT Terminal RS-232C Terminal D-sub 9 Pin DVI Terminal DVI-D 24 PinControl Panel Indicator Display on the Control Panel Remote Control Loading Batteries into the Remote Control Precautions for Using BatteriesOpen the back cover Load the batteriesInstalling the Projector Installation EnvironmentPrecaution for Usage Adjusting the InclinationProjector and Screen Installation Precautions for Ceiling-mountMounting this Unit  Screen Installation Screen Size and Projection DistanceEffective Range of Remote Control Unit  When reflecting off a screen When directing remote control unit toward this unit Connecting to Various Devices Connecting to DevicesRight Side of this unit  Control from external deviceConnecting the Power Cord supplied When using this unit, remove the lens capBasic Operation Procedures Turning on the powerAdjusting zoom screen size Adjusting focusTurning off the power Pull out the power plug from the power outletHiding the image temporarily Press HideAdjustments and Settings Using Menus Menu StructureButton Function This Unit Remote Control Unit Menu Operation ButtonsPress the Menu button Press 5/ ∞ to select a main menu item and EnterTo confirm Menu Configuration Image adjust MenuSet up Menu Options MenuPress 5/∞ to select Set up, followed by pressing Screen MaskingProject image onto the screen Press the Menu buttonPicture Shift Setting Press 5/∞ to select Options, followed by press Ing EnterAbout Lamp Replacement Replacing the LampLight-source Lamp and Lamp Usage Time Loosen the screws on the lamp unit and lift up the handle Pull out the lamp unitInsert the new lamp unit until it is fully Tighten the screws of the lamp unit Close the handleResetting Lamp Time Insert plug into the power outletTo ensure the lamp time has been reset ExitCleaning and Replacing the Filter What to do when these messages are displayed Message Cause Details About warning indicators IndicatorPlease follow the procedures below  Actions to be taken upon warning indicationsTroubleshooting Pin No Signal Name Terminal DescriptionPin Arrangement  RS-232C TerminalRS-232C External Control External control command table Operation mode Only Asking command is possibleSpecial parameters Specifications  Dimensions Unit mm Top FrontBottom SideMF2MIman v0.90ß