Meridian Audio D-ILA 1080MF2 operation manual  About warning indicators, Indicator

Page 33
Perform procedures to turn on/off the power again.
After checking if an impact shock has not occurred during operation, perform procedures to turn on/off the power again.
When the warning on lamp time is displayed, remove the power plug when the [STAND BY] indicator is still on, followed by installing a new lamp.
Perform procedures to turn on/off the power again.

Warning Indication

About warning indicators

If abnormality occurs in this unit during projection, the warning mode will be triggered and the type of abnormality will be indicated by a combination of indicators displayed on the control panel. This unit will then automatically stop projection and run the cooling fan for about 90 seconds.

No.

 

 

 

 

 

 

 

 

 

Indicator

 

 

 

 

Warning

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[LAMP]

 

[TEMP]

[STAND BY]

 

[OPERATE]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Blinking

 

 

 

 

 

 

Blinking

 

 

 

 

Lamp does not light up and unit is unable to project

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Blinking

 

 

 

 

 

 

Blinking Simultaneously

 

 

 

 

Blinking

Lamp turned off during projection

 

 

 

 

 

 

 

 

 

Lamp usage time has exceeded 2010 hours

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

Blinking

 

Blinking

 

 

 

 

 

 

 

 

Circuits are not functioning properly (Circuit Operation Error)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Blinking

 

 

 

 

 

 

 

Blinking Alternately

 

 

 

 

 

 

Blinking

Lamp cover is not installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

Blinking

 

 

 

 

 

 

 

 

Internal temperature is abnormally high (Internal Temperature Error)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

Blinking

Blinking

 

 

 

 

Temperature at air inlets are high (External Temperature Error)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

Blinking

 

Blinking

Blinking

 

 

 

Blinking

Inner fan has stopped (Fan Locked)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

●For details on individually blinking indicators, please refer to Page 28.

Actions to be taken upon warning indications

Please follow the procedures below.

For Nos. 1-3

No. 1:

No. 2:

No. 3: For Nos. 4-7

Remove the power plug when the [STAND BY] indicator is on. After that, check No. 4 - No. 7.

No. 4: Ensure that the lamp unit is correctly mounted onto this unit. Next, ensure that the lamp cover is correctly mounted. After that, restart according to the basic operation procedures.

No. 5: Check that nothing is blocking the air inlets, and wait until the inside cools down. After that, restart according to the basic operation procedures.

No. 6: Check the ambient temperature. If it is normal, leave the unit until it cools down. After that, restart according to the basic operation procedures.

No. 7: Leave the unit until it cools down. After that, restart according to the basic operation procedures.

If the warning indication is displayed again, wait for the cooling fan to stop. Check that the [STAND BY] indicator is on, followed by removing the plug from the power outlet. Call your authorized dealer for repair.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents ILA 1080MF2 FCC Information U.S.A. only About the installation placeMachine Noise Information Germany only About burning-in of the D-ILA devicePower cord Do not allow any unqualified person to install the unitDo not cut off the main plug from this equipment How To Replace The FuseStandard for gauging replacement time of components Accessories ContentsFront Side/Top Surface/Left Side Controls and FeaturesRear Side/Right Side/Bottom Surface Service Terminal Connector PanelSync OUT Terminal RS-232C Terminal D-sub 9 Pin DVI Terminal DVI-D 24 PinControl Panel Indicator Display on the Control Panel Remote Control Precautions for Using Batteries Loading Batteries into the Remote ControlOpen the back cover Load the batteriesInstallation Environment Installing the ProjectorPrecaution for Usage Adjusting the InclinationProjector and Screen Installation Precautions for Ceiling-mountMounting this Unit Screen Size and Projection Distance  Screen InstallationEffective Range of Remote Control Unit  When reflecting off a screen When directing remote control unit toward this unit Connecting to Devices Connecting to Various DevicesRight Side of this unit  Control from external deviceWhen using this unit, remove the lens cap Connecting the Power Cord suppliedTurning on the power Basic Operation ProceduresAdjusting zoom screen size Adjusting focusPull out the power plug from the power outlet Turning off the powerHiding the image temporarily Press HideMenu Structure Adjustments and Settings Using MenusMenu Operation Buttons Button Function This Unit Remote Control UnitPress the Menu button Press 5/ ∞ to select a main menu item and EnterTo confirm Image adjust Menu Menu ConfigurationSet up Menu Options MenuScreen Masking Press 5/∞ to select Set up, followed by pressingProject image onto the screen Press the Menu buttonPress 5/∞ to select Options, followed by press Ing Enter Picture Shift SettingAbout Lamp Replacement Replacing the LampLight-source Lamp and Lamp Usage Time Pull out the lamp unit Loosen the screws on the lamp unit and lift up the handleInsert the new lamp unit until it is fully Tighten the screws of the lamp unit Close the handleInsert plug into the power outlet Resetting Lamp TimeTo ensure the lamp time has been reset ExitCleaning and Replacing the Filter Message Cause Details What to do when these messages are displayedIndicator  About warning indicatorsPlease follow the procedures below  Actions to be taken upon warning indicationsTroubleshooting Terminal Description Pin No Signal NamePin Arrangement  RS-232C TerminalRS-232C External Control External control command table Operation mode Only Asking command is possibleSpecial parameters Specifications Front  Dimensions Unit mm TopBottom SideMF2MIman v0.90ß
Top Page Image Contents