Meridian Audio D-ILA 1080MF2 operation manual Cleaning and Replacing the Filter

Page 31

Cleaning and Replacing the Filter

Clean the filter regularly or air intake efficiency may deteriorate and malfunction may occur. If the filter is extremely dirty and cannot be cleaned, or if it is damaged, replace the filter with a new one (lower filter: LC32087-002A / inner filter: LC32058- 002A). Otherwise, dirt may enter the unit and appear on the screen, preventing you from enjoying the video fully. If dirt has entered the unit or if you need information about the filter, please consult your authorized dealer.

The air inlet filter on the right side cannot be removed. Please clean this filter regularly with, for example, a vacuum

cleaner.

1 Pull out the plug from the power outlet

Pull out the power plug from the outlet while the [STAND BY] indicator is still on.

2 Remove the lower filter

Withdraw the filter backwards along the rail in the direc- tion of the arrow.

3 Remove the inner filter

Push up and lift the claw at the base of the inner filter,

followed by drawing out the filter.

Claw

Lower Filter

Inner Filter

4 Clean the filter

Clean the filter with water and dry it, avoiding direct sun- light. In extremely soiled cases, use of a neutral deter- gent is recommended.

5 Reinstall the lower filter

Reinstall the lower filter by inserting it into this unit.

6 Reinstall the inner filter

Install after engaging the 2 claws at the upper part of the inner filter to this unit.

Put on rubber gloves when using a neutral detergent.

After washing a filter with water, make sure that the filter is completely dry before reinstalling. Otherwise, electric shocks or malfunctions may occur.

Do not clean lower filters and inner filters with a vacuum cleaner. Since these filters are soft, they may be dam- aged if they are sucked into the vacuum cleaner.

Lower Filter

Inner Filter

Claw

31

Image 31
Contents ILA 1080MF2 About burning-in of the D-ILA device About the installation placeFCC Information U.S.A. only Machine Noise Information Germany onlyPower cord Do not allow any unqualified person to install the unitDo not cut off the main plug from this equipment How To Replace The FuseStandard for gauging replacement time of components Accessories ContentsFront Side/Top Surface/Left Side Controls and FeaturesRear Side/Right Side/Bottom Surface DVI Terminal DVI-D 24 Pin Connector PanelService Terminal Sync OUT Terminal RS-232C Terminal D-sub 9 PinControl Panel Indicator Display on the Control Panel Remote Control Load the batteries Loading Batteries into the Remote ControlPrecautions for Using Batteries Open the back coverAdjusting the Inclination Installing the ProjectorInstallation Environment Precaution for UsagePrecautions for Ceiling-mount Projector and Screen InstallationMounting this Unit Screen Size and Projection Distance  Screen Installation When reflecting off a screen Effective Range of Remote Control Unit When directing remote control unit toward this unit  Control from external device Connecting to Various DevicesConnecting to Devices Right Side of this unitWhen using this unit, remove the lens cap Connecting the Power Cord suppliedAdjusting focus Basic Operation ProceduresTurning on the power Adjusting zoom screen sizePress Hide Turning off the powerPull out the power plug from the power outlet Hiding the image temporarilyMenu Structure Adjustments and Settings Using MenusMenu Operation Buttons Button Function This Unit Remote Control UnitPress 5/ ∞ to select a main menu item and Enter Press the Menu buttonTo confirm Options Menu Menu ConfigurationImage adjust Menu Set up MenuPress the Menu button Press 5/∞ to select Set up, followed by pressingScreen Masking Project image onto the screenPress 5/∞ to select Options, followed by press Ing Enter Picture Shift SettingReplacing the Lamp About Lamp ReplacementLight-source Lamp and Lamp Usage Time Tighten the screws of the lamp unit Close the handle Loosen the screws on the lamp unit and lift up the handlePull out the lamp unit Insert the new lamp unit until it is fullyExit Resetting Lamp TimeInsert plug into the power outlet To ensure the lamp time has been resetCleaning and Replacing the Filter Message Cause Details What to do when these messages are displayed Actions to be taken upon warning indications  About warning indicatorsIndicator Please follow the procedures belowTroubleshooting  RS-232C Terminal Pin No Signal NameTerminal Description Pin ArrangementRS-232C External Control Operation mode Only Asking command is possible External control command tableSpecial parameters Specifications Side  Dimensions Unit mm TopFront BottomMF2MIman v0.90ß