ENGLISH
Lamp Replacement Precautions
•Replacing the lamp runs the risk of burns and electric shock, therefore shut off power supply, unplug the AC power cable from its electrical outlet and wait at least 60 min for the lamp to cool down before attempting to replace it.
•If the lamp breaks, contact your nearest Marantz Authorized Dealer or Service Center.
Lens Changes
•The lens of this projector can be changed as liked. (LN-
Lens | Projection distance of 100 inch image |
LN10VP32 | Approx. 3.19 to 3.98 m |
LN10VP40 | Approx. 3.98 to 5.31 m |
LN10VP53 | Approx. 5.31 to 7.97 m |
CAUTION | CAUTION HOT |
|
ATTENTION | ATTENTION CHAUD | 高 温 注 意 |
| ||
VORSICHT | WARNUNG HEISS | 警 告 |
| ||
|
|
|
CAUTION | WARNING |
THIS COVER IS PROVIDED WITH | |
CONTAINS MERCURY, | INTERLOCK TO REDUCE THE RISK OF |
DON'T PUT IN TRASH. | EXCESSIVE ULTRAVIOLET RADIATION. |
DO NOT DEFEAT ITS PORPOSE OR | |
RECYCLE OR DISPOSE | ATTEMPT TO SERVICE WITHOUT |
AS HAZARDOUS WASTE | REMOVING COVER COMPLETELY. |
|
|
VIDEO IN | COMPONENTVIDEO IN 2 |
|
|
| ||||
| Y | PB/CB PR/CR | Y | PB/CB | PR/CR |
|
|
|
|
|
|
| REMOTE |
| TRIG. | LIGHT |
|
RGB IN |
| IN | 1 |
|
| |||
|
|
|
| INT. EXT. |
|
| OFF ON |
|
|
|
|
|
| OUT | 2 |
|
|
|
|
|
|
|
| OFF | ON |
|
|
|
|
|
|
| AC IN |
| |
|
|
|
|
|
| ～ |
| |
|
|
|
|
|
| ＭＯＤＥＬ ＮＯ．ＶＰ１０Ｓ１／Ｕ１Ｍ | ||
|
|
|
|
|
| ＡＣ１２０Ｖ～ ６０Ｈｚ Ｘ．ＸＡ | ||
|
|
|
|
|
|
| ＭＡＤＥ ＩＮ | ＪＡＰＡＮ |
*The above projections distances are given for a screen with an aspect ratio of 16:9. For screen sizes and projection distances by lens, see pg.
•To change the lens, contact your nearest Marantz Authorized Dealer or Service Center.
Do not change the lens yourself.
•The lenses used with this projector are as follows.
CAUTION
ATTENTION
LA LAMPE SOUS HAUTE PRESSION PEUT EXPLOSER SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE.
VORSICHT
BEI FALSCHER HANDHABUNG KANN DIE HOCHDRUCKLAMPE EXPLODIEREN UBERLASSEN SIE WARTUNGSARBEITEN NUR FACHPERSONAL.
CAUTION HOT
UNPLUG THE POWER CORD AND WAIT 60 MINUTES BEFORE CHANGING THE LAMP.
ATTENTION CHAUD
DEBRANCER LE CORD ON D'ALIMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER AB UND WARTEN SIE 60 MINUTEN BEVOR SIE DIE GLUHLAMPE WECHSELN.
ラン
セン
行っ
高圧
破裂
際は
ださ
Projector | Lens |
(Found on rear panel nameplate) |
|
|
|
VP10S1L32/N1M | LN10VP32 |
VP10S1L40/N1M | LN10VP40 |
VP10S1L53/N1M | LN10VP53 |
•Before replacing the lamp, read carefully “Lamp Handling
Precautions” (☞ pg. 1) and “Lamp Unit Replacement” (☞ pg. 36). Replace the lamp as explained therein.
4