Sharp AR-5316, AR-5320 Cleaning the Bypass Tray Paper Feed Roller, Cleaning the Transfer Charger

Page 59

ROUTINE MAINTENANCE

CLEANING THE BYPASS TRAY PAPER FEED ROLLER

If misfeeds occur frequently when feeding envelopes, thick paper, etc. through the bypass tray, wipe the paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water.

Paper feed roller

CLEANING THE TRANSFER CHARGER

If copies start becoming streaky or blotchy, the transfer charger may be dirty.

Clean the charger using the following procedure.

1 Turn the power switch off.

2 Open the bypass tray and the side cover.

3 Lift and pull out the upper paper tray.

4 Take the charger cleaner out by holding the tab.

5 Set the charger cleaner onto the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times.

If the white sheet metal is smudged with toner, wipe it with a soft, clean cloth.

Slide the charger cleaner from one end to the

Note other end along the groove of the transfer

6

charger. If the cleaner is stopped on the way,

smudges on copies may occur.

6 Return the charger cleaner to its original position. Close the upper paper tray. Close the side cover by pressing the handle on the cover.

7 Turn the power switch on.

Charger cleaner

57

Page 58 Page 60
Image 59
Page 58 Page 60
Contents AR-5320/AR-5320 AR-5316/AR-5316Page Contents Peripheral Devices and Supplies Air conditioner or Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Changes, e.g., near anDo not touch the photoconductive drum green portion Environmental InformationTrademark acknowledgements SPF Using the ManualMeaning of R in Original and Paper Size Indications Conventions Used in this ManualPaper trays Differences Between ModelsAB series metric and inch series references Copy speedMain Features Part Names and Functions Fusing unit paper guide Open to remove misfed paper Parallel connectorDocument feeder tray when the SPF is installed Fusing unit release leversOperation Panel Paper feed location / misfeed location indicators Paper Size indicatorsSPF indicator when the SPF is installed Auto Image key Auto % / indicatorPower Save Modes Power on and OFFPower on Power OFFSpecial papers Paper tray type Paper type Size Weight CapacityLoading Paper PaperFan the paper Loading PaperLoading the paper tray Locks in placeSet the paper guides to the copy paper width Important points when inserting paper in the bypass trayLoading the bypass tray Envelopes Changing a TRAY’S Paper Size SettingPress the Start key and then the Paper Size Enter key Important points when using the printer modeOpen the document cover/SPF, and place the original Normal CopyingCopying from the document glass Set the originals face up in the document feeder tray Copying from the SPFOriginals that can be used in the SPF Auto paper select mode Two-tray model onlyStream feeding mode Removing the document coverOriginal types Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Selecting the TrayAutomatic Ratio Selection Setting the Number of CopiesImportant note when making a large number of copies REDUCTION/ENLARGEMENT/ZOOMPress the Auto Image key Auto % Selecting a preset ratioFine adjustment of the ratio Manual Ratio SelectionPress the Copy ratio display key XY Zoom copyingPress the Copy ratio display key Place original B as shown below TWO-SIDED Copying Using the Bypass TrayCopy original a Press the Dual page Copy key Copy indicator Is litDual page Copying Set the original size to A3 11 xReplace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Make sure that paper is loaded in the tray Using the Printer ModeBasic Procedure for Printing Important points when setting the paper sizeOperation in Copy and Printer Modes Pausing a print jobWhen Use close paper size is disabled When Use close paper size is enabledAdjusting the Automatic Exposure Level Save mode, make sure Toner Save Mode and High Image Quality ModeWhen enabling toner Photo indicator stops blinking and lights steadilyUser Programs Customising SettingsShort beep Explanation300 dpi MinimumBase settings Selecting a Setting for a User ProgramAuditing Mode Settings Settings for Auditing ModeAuditing Mode For the setting codes, see Auditing Mode SETTINGS. p.36 Selecting Auditing Mode SettingsAccount number deletion Auditing modeAccount number entry Account number changeCopying when Auditing mode is enabled Resetting accountTroubleshooting MACHINE/COPYING Problems Paper misfeed Too much paper is loaded in the tray Problem Cause and solution Misfeed occursPaper is not loaded properly Pieces of paper inside machineCopying or printing is performed Any other indicators are litOriginal smudged or blotchy Copies Transfer charger is dirtyPrinting Problems Click Add or Remove Programs Removing the softwareClick the start button, and then click Control Panel Indicators and Display Messages Section a Misfeed RemovalMisfeed in the SPF Remove the misfed originalSection C Misfeed indicator will go outMisfeed in the Bypass Tray Misfeed in the paper feed area Misfeed in the MachineMisfed paper during Misfeed in the fusing areaAllow easier removal Be careful not to tear the misfed paper during Misfeed in the transport areaClose the side cover Be careful not to tear the misfed paper during removalPush the upper paper tray in completely Misfeed in the Upper Paper TrayClose the upper paper tray Close the lower paper tray Open the lower side coverRemove the misfed paper Close the lower side coverDiscard the shutter Toner cartridge replacement required Indicator will go outReplacing the Toner Cartridge Close the front coverTotal copy count Checking the Total Output Count and Toner LevelChecking the Total Output Count Total output countPress the Light key to return to the normal display Routine MaintenanceCleaning the Document Glass and SPF/ Document Cover Checking the Toner LevelCleaning the Transfer Charger Cleaning the Bypass Tray Paper Feed RollerSingle Pass Feeder SpecificationsPeripheral Devices Store paper in the wrapper and lying flat Storage of SuppliesProper Storage Store the supplies in a location that isSpecifications Printer Function Software License Page Index Symbols10, 13 Preset Ratio selector indicatorTroubleshooting Original typesIndicators, lit and blinking Machine settingsProblem occurs Memo Class Laser Product Laser Klasse Page Sharp Corporation
Related manuals
Manual 16 pages 45.89 Kb

AR-5316, AR-5316 X, AR-5320, AR-5320 X specifications

The Sharp AR-5316, AR-5320, AR-5320 X, and AR-5316 X are a series of multifunctional printers/copiers that combine efficiency, productivity, and advanced technology to meet the needs of modern offices. These models are designed to handle a variety of tasks including printing, copying, scanning, and faxing, making them ideal for small to medium-sized businesses.

One of the main features of these models is their speed. The AR-5316 is capable of producing up to 16 pages per minute, while the AR-5320 and AR-5320 X push that speed to an impressive 20 pages per minute. This efficient output reduces wait times and enhances productivity, ensuring that your office can keep up with demanding workloads.

In terms of print quality, the Sharp AR series stands out with a resolution of up to 600 x 600 dpi. This provides crisp and clear documents, essential for professional presentations and important paperwork. Furthermore, these models support various media sizes, accommodating everything from standard letter-size paper to larger formats, which gives users flexibility when printing.

Another significant feature is the user-friendly interface. The AR-5320 X and AR-5316 X include a color touchscreen display, allowing for intuitive navigation and easy operation. This makes it simple for any staff member to quickly access essential features without extensive training.

In addition to traditional printing and copying functions, these devices also come equipped with advanced scanning capabilities. The AR-5320 X, for example, offers duplex scanning, allowing users to scan both sides of a document in a single pass. This not only saves time but also enhances productivity by streamlining workflow.

Security is another major consideration in today's office environments. The Sharp AR series includes a range of security features, such as secure printing options and user authentication, ensuring that sensitive information remains protected from unauthorized access.

Energy efficiency is also a key characteristic of these models. They comply with Energy Star standards, helping businesses reduce their energy consumption and overall operating costs. With features like automatic power shut-off, these copiers are designed to be environmentally friendly while still delivering high performance.

Overall, the Sharp AR-5316, AR-5320, AR-5320 X, and AR-5316 X offer a robust set of features designed to enhance office efficiency and productivity. With their combination of speed, quality, and advanced functionality, these devices are well-suited for any office looking to streamline their document management processes.
Top Page Image Contents