Sharp AL-1650 operation manual Copier Installation, Do not install your copier in areas that are

Page 10

COPIER INSTALLATION

GETTING STARTED

Copier installation

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

● damp, humid, or very dusty

● exposed to direct sunlight

● poorly ventilated

● subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing and proper ventilation.

4" (10 cm)

A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

8

Image 10

Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Paper Size indicators AUTO/MANUAL/PHOTO / / key and indicators pOriginal Size Enter key and indicators p Alarm indicatorsAuto Image key and indicator p Dual page Copy key and indicator pLight and dark keys and indicators @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Front of the paper tray Turn the power switch on Load copy paperSET-UP Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Adjust the copy density Using the SPFTurn the power switch on Normal CopyingNormal Copying Set the number of copies using the two copy quantity KeysStream feeding mode Press the Start keyUsing the original table Normal Copying Press the Auto Image Key REDUCTION/ENLARGEMENT/ZOOMAutomatic Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display Key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyStart key to resume copying Interrupting a Copy RUNPress the Interrupt key Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Press the AUTO/MANUAL/PHOTO Key To select the Manual Mode Toner Save ModeTo enter the toner save mode, press the light key TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement Cartridge out until the green strap handle can be grasped To remove itBy the right hand. Lift the cartridge by the handle while Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeFirst confirm the misfeed location Misfeed RemovalMisfeed in the SPF Right feeding roller cover and remove the misfedMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray Gently pull the misfed paper outRemoving it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperMisfeed in the lower paper tray Misfeed in the upper paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper User Programs Setting the user programsEnter a program number using the left copy quantity Key List of user programsSelect the desired parameter using the right copy quantity User ProgramsPreheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode Bypass tray paper feed roller User MaintenanceOriginal table and document feeder cover Transfer chargerCharger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic functionExample Supply part numbers SuppliesTypes and sizes of copy paper Supply listProper storage SuppliesGenuine supplies statement Store copy paper in the wrapper and lying flatMoving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsOther Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Memo Memo Page Sharp Corporation