Sharp AL-1650 operation manual Normal Copying

Page 21

NORMAL COPYING

●For photographs, select PHOTO ( ) and then adjust with the light

( ) and dark ( ) keys as desired.

● There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.)

If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously.

Set the number of copies using the two copy quantity

6 ( , ) keys.

● Press the right copy quantity key to set the units digit from 0 to 9. This key will not change the tens digit.

●Press the left copy quantity key to set the tens digit from 1 to 9.

● A single copy can be made with the initial setting, i.e., when “0” is displayed.

Tens digit	Units digit	●	Press the CLEAR (	) key to clear an entry if a mistake is made.

7	Press the START (	) key.
7	● The number in the copy quantity display will decrease by 1 each time
	a copy is made.
	● Press the CLEAR (	) key to stop copying in the middle of a run.
	● To repeat the same copy sequence for a different original, simply
	replace the original and press the START (		) key.

MAKING COPIES

Normal copying

19

Image 21

Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Original Size Enter key and indicators p AUTO/MANUAL/PHOTO / / key and indicators pPaper Size indicators Alarm indicatorsLight and dark keys and indicators Dual page Copy key and indicator pAuto Image key and indicator p @0 Preset Ratio selector keys and indicators pDo not install your copier in areas that are Copier InstallationGetting Started Unpacking Checking Packed Components and AccessoriesInstall the TD cartridge SET-UPGently lift and pull out the paper tray until it stops SET-UP Turn the power switch on Load copy paperFront of the paper tray Store the pressure plate lock which has been removedPush the paper tray firmly back into the copier Loading Copy PaperLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Turn the power switch on Using the SPFAdjust the copy density Normal CopyingStream feeding mode Set the number of copies using the two copy quantity KeysNormal Copying Press the Start keyUsing the original table Normal Copying Automatic REDUCTION/ENLARGEMENT/ZOOMPress the Auto Image Key Enter the number of copies Press the Start keyManual REDUCTION/ENLARGEMENT/ZOOMUnfold the bypass tray Bypass Feed special paperPress the Tray Select key to select the bypass Bypass Feed special paperTWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display Key Set the number of copies and press the Start key XY ZoomPress the B/W Reverse key Check the copy paper size ReversePress the Dual page Copy key Dual page CopyPress the Interrupt key Interrupting a Copy RUNStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode Press the AUTO/MANUAL/PHOTO Key To select the Manual ModeTo enter the toner save mode, press the light key Genuine Supplies TD Cartridge ReplacementTD Cartridge Replacement To remove it Cartridge out until the green strap handle can be graspedBy the right hand. Lift the cartridge by the handle while Gently install the TD cartridge. To install the TD cartridge Drum Cartridge ReplacementMisfeed in the SPF Misfeed RemovalFirst confirm the misfeed location Right feeding roller cover and remove the misfedMisfeed in the bypass tray Misfeed RemovalMisfeed in the copier Gently pull the misfed paper outFusing unit is hot. Take care in removing paper Removing itPush gently the right side of the front cover to open Cover On either side of the guide and remove the misfed paper Open the paper guide by pressing down the projectionMisfeed in the upper paper tray Misfeed in the lower paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper Enter a program number using the left copy quantity Key Setting the user programsUser Programs List of user programsUser Programs Select the desired parameter using the right copy quantityPower Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode Original table and document feeder cover User MaintenanceBypass tray paper feed roller Transfer chargerUser Maintenance Charger cleaner out by holding the tabGently lift and pull out the upper paper tray and take Copier TROUBLE? Problem SolutionSelf-diagnostic function Copier TROUBLE?Example Types and sizes of copy paper SuppliesSupply part numbers Supply listGenuine supplies statement SuppliesProper storage Store copy paper in the wrapper and lying flatTurn the power switch off and disconnect the power Cord Moving InstructionsPush the paper tray back into the copier Copier SpecificationsSingle Pass Feeder SpecificationsIndex Index Material Safety Data Sheet Special Fire Fighting Procedure Ignition TemperatureFlash Point Method Used Flammable LimitsIngredients CAS No Proportion Other LimitsHealth Hazards None required under normal use Memo Memo Page Sharp Corporation