Sharp AL-1650 operation manual Part Names and Functions

Page 6

PART NAMES AND FUNCTIONS

GETTING STARTED

Part names and functions

Overall layout

				e
	q
			o
	w			!1
	w
		y	!0	!2
	e		!0	!3
	e

u

r t

!4

i

qDocument feeder cover

Open to make copies from the original table.

wOriginal table

All originals which cannot be copied from the SPF must be copied here.

eHandles

Use to move the copier.

rPower switch

Press to turn copier power on and off.

tOperation panel

All copier controls are located here for easy operation.

yPaper output tray

Finished copies are deposited in the paper output tray.

uFront cover

Open to remove misfeeds and for copier servicing.

iPaper tray

Each tray holds 250 sheets of copy paper.

oSide cover

Open to remove misfeeds and to service the copier.

!0 Side cover handle

Lift and pull to open the side cover.

!1 Bypass tray guides

Adjust to the width of the copy paper.

!2 Bypass tray

Special papers (including transparency film) and copy paper can be fed from the bypass tray.

!3 Bypass tray extension

Pull out when feeding large paper such as 8-1/2" x 14" and 11" x 17".

!4 Charger cleaner

Use to clean the transfer charger.

4

Image 6

Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Paper Size indicators AUTO/MANUAL/PHOTO / / key and indicators pOriginal Size Enter key and indicators p Alarm indicatorsAuto Image key and indicator p Dual page Copy key and indicator pLight and dark keys and indicators @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingInstall the TD cartridge SET-UPGently lift and pull out the paper tray until it stops Front of the paper tray Turn the power switch on Load copy paperSET-UP Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Adjust the copy density Using the SPFTurn the power switch on Normal CopyingNormal Copying Set the number of copies using the two copy quantity KeysStream feeding mode Press the Start keyUsing the original table Normal Copying Press the Auto Image Key REDUCTION/ENLARGEMENT/ZOOMAutomatic Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display Key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyStart key to resume copying Interrupting a Copy RUNPress the Interrupt key Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode Press the AUTO/MANUAL/PHOTO Key To select the Manual ModeTo enter the toner save mode, press the light key TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement To remove it Cartridge out until the green strap handle can be graspedBy the right hand. Lift the cartridge by the handle while Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeFirst confirm the misfeed location Misfeed RemovalMisfeed in the SPF Right feeding roller cover and remove the misfedMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray Gently pull the misfed paper outFusing unit is hot. Take care in removing paper Removing itPush gently the right side of the front cover to open Cover Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperMisfeed in the upper paper tray Misfeed in the lower paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper User Programs Setting the user programsEnter a program number using the left copy quantity Key List of user programsSelect the desired parameter using the right copy quantity User ProgramsPower Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode Bypass tray paper feed roller User MaintenanceOriginal table and document feeder cover Transfer chargerUser Maintenance Charger cleaner out by holding the tabGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Self-diagnostic function Copier TROUBLE?Example Supply part numbers SuppliesTypes and sizes of copy paper Supply listProper storage SuppliesGenuine supplies statement Store copy paper in the wrapper and lying flatTurn the power switch off and disconnect the power Cord Moving InstructionsPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsIngredients CAS No Proportion Other LimitsHealth Hazards None required under normal use Memo Memo Page Sharp Corporation