Sharp AL-1650 Set-Up, Front of the paper tray, Turn the power switch on Load copy paper

Page 14

SET-UP

GETTING STARTED

Set-up

	Pressure	Store the pressure plate lock which has been removed
	Pressure	6 in step 5 and the screw which has been removed in step
	plate lock	6 in step 5 and the screw which has been removed in step
		2 in the front of the paper tray.

● To store the pressure plate lock, rotate the lock to fix it on the relevant location.

●Follow steps 4 to 6 for both the upper and lower trays except for storage of the screw.

Screw

Ensure that the power switch of the copier is in the OFF

7 position. Plug the power cord into the nearest outlet.

Power on	8
	9

If you use the copier in a country other than the country where the copier was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the copier into an incompatible power supply, irreparable damage to the copier will result.

Only insert the power cord into a properly grounded wall socket.

Do not use extension cords or power strips.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Turn the power switch on.

Load copy paper.

●When loading copy paper for the first time, be sure to turn the power switch on in advance.

●For loading copy paper, see steps 2 to 4 of LOADING COPY PAPER on page 13. To change the paper size from the factory default size, see pages 14 and 15.

12

Image 14

Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Paper Size indicators AUTO/MANUAL/PHOTO / / key and indicators pOriginal Size Enter key and indicators p Alarm indicatorsAuto Image key and indicator p Dual page Copy key and indicator pLight and dark keys and indicators @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingGently lift and pull out the paper tray until it stops Install the TD cartridgeSET-UP Front of the paper tray Turn the power switch on Load copy paperSET-UP Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Adjust the copy density Using the SPFTurn the power switch on Normal CopyingNormal Copying Set the number of copies using the two copy quantity KeysStream feeding mode Press the Start keyUsing the original table Normal Copying Press the Auto Image Key REDUCTION/ENLARGEMENT/ZOOMAutomatic Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying Press the copy ratio display Key XY ZoomPress the XY-ZOOM key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyStart key to resume copying Interrupting a Copy RUNPress the Interrupt key Replace the original for the interrupted job and pressAutomatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the AUTO/MANUAL/PHOTO Key To select the Manual Mode TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement By the right hand. Lift the cartridge by the handle while To remove itCartridge out until the green strap handle can be grasped Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeFirst confirm the misfeed location Misfeed RemovalMisfeed in the SPF Right feeding roller cover and remove the misfedMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray Gently pull the misfed paper outPush gently the right side of the front cover to open Cover Fusing unit is hot. Take care in removing paperRemoving it Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperClose the side cover by pressing the handle on the cover Misfeed in the upper paper trayMisfeed in the lower paper tray Remove the misfed paper User Programs Setting the user programsEnter a program number using the left copy quantity Key List of user programsSelect the desired parameter using the right copy quantity User ProgramsAuto power shut-off mode Power Save ModesPreheat mode Copying from the preheat mode Power Save ModesSetting the power save modes Bypass tray paper feed roller User MaintenanceOriginal table and document feeder cover Transfer chargerGently lift and pull out the upper paper tray and take User MaintenanceCharger cleaner out by holding the tab Problem Solution Copier TROUBLE?Example Self-diagnostic functionCopier TROUBLE? Supply part numbers SuppliesTypes and sizes of copy paper Supply listProper storage SuppliesGenuine supplies statement Store copy paper in the wrapper and lying flatPush the paper tray back into the copier Turn the power switch off and disconnect the power CordMoving Instructions Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsHealth Hazards Ingredients CAS No ProportionOther Limits None required under normal use Memo Memo Page Sharp Corporation