Sharp AL-1650 operation manual Safety Precautions

Page 4

CAUTIONS

GETTING STARTED

Cautions

Follow the cautions below when using this copier.

●The fusing area is hot. Exercise care in this area when removing misfed paper.

●Do not look directly at the light source. Doing so may damage your eyes.

●The socket-outlet shall be installed near the equipment and shall be easily accessible.

●Place the copier on a firm, level surface.

● Do not install the copier in a humid or dusty location.

● When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

●When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet.

●Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the copier.

SAFETY PRECAUTIONS

This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the copier does not produce hazardous laser radiation. For your safety, observe the precautions below.

●Do not remove the cabinet, operation panel or any other covers.

●The copier’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

2

Image 4

Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions AUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators pPaper Size indicators Alarm indicatorsDual page Copy key and indicator p Light and dark keys and indicatorsAuto Image key and indicator p @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Using the SPF Turn the power switch onAdjust the copy density Normal CopyingSet the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start keyUsing the original table Normal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display Key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Press the AUTO/MANUAL/PHOTO Key To select the Manual Mode Toner Save ModeTo enter the toner save mode, press the light key TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement Cartridge out until the green strap handle can be grasped To remove itBy the right hand. Lift the cartridge by the handle while Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeMisfeed Removal Misfeed in the SPFFirst confirm the misfeed location Right feeding roller cover and remove the misfedMisfeed Removal Misfeed in the bypass trayMisfeed in the copier Gently pull the misfed paper outRemoving it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperMisfeed in the lower paper tray Misfeed in the upper paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper Setting the user programs Enter a program number using the left copy quantity KeyUser Programs List of user programsSelect the desired parameter using the right copy quantity User ProgramsPreheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode User Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer chargerCharger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic functionExample Supplies Types and sizes of copy paperSupply part numbers Supply listSupplies Genuine supplies statementProper storage Store copy paper in the wrapper and lying flatMoving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsOther Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Memo Memo Page Sharp Corporation