Sharp AL-1650 Removing it, Push gently the right side of the front cover to open Cover

Page 40

MISFEED REMOVAL

STATUS INDICATORS Misfeed removal

2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below.

If paper is misfed here, proceed to “B. Misfeed in the fusing area”.

If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”.

If paper is misfed here, proceed to “A. Misfeed in the paper feed area”.

A. Misfeed in the paper feed area

Push gently the right side of the front cover to open the

1 cover.

 

2

Carefully remove the misfed paper. Turn the roller

 

rotating knob in the direction of the arrow to assist in

 

 

Roller rotating knob

 

removing it.

 

 

 

 

The fusing unit is hot. Take care in removing paper.

Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. Doing so may damage the drum and cause smudges on copies.

Close the front cover by pushing both sides with your

3 hands and then close the side cover by pressing the handle on the cover.

The misfeed ( ) indicator will go out.

When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.

B. Misfeed in the fusing area

Push gently the right side of the front cover to open the

1 cover.

38

Image 40
Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions AUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators pPaper Size indicators Alarm indicatorsDual page Copy key and indicator p Light and dark keys and indicatorsAuto Image key and indicator p @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeGently lift and pull out the paper tray until it stops Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Using the SPF Turn the power switch onAdjust the copy density Normal CopyingSet the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start keyUsing the original table Normal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display Key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Press the AUTO/MANUAL/PHOTO Key To select the Manual Mode Toner Save ModeTo enter the toner save mode, press the light key TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement Cartridge out until the green strap handle can be grasped To remove itBy the right hand. Lift the cartridge by the handle while Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeMisfeed Removal Misfeed in the SPFFirst confirm the misfeed location Right feeding roller cover and remove the misfedMisfeed Removal Misfeed in the bypass trayMisfeed in the copier Gently pull the misfed paper outRemoving it Fusing unit is hot. Take care in removing paperPush gently the right side of the front cover to open Cover Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperMisfeed in the lower paper tray Misfeed in the upper paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper Setting the user programs Enter a program number using the left copy quantity KeyUser Programs List of user programsSelect the desired parameter using the right copy quantity User ProgramsPreheat mode Power Save ModesAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode User Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer chargerCharger cleaner out by holding the tab User MaintenanceGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Copier TROUBLE? Self-diagnostic functionExample Supplies Types and sizes of copy paperSupply part numbers Supply listSupplies Genuine supplies statementProper storage Store copy paper in the wrapper and lying flatMoving Instructions Turn the power switch off and disconnect the power CordPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsOther Limits Ingredients CAS No ProportionHealth Hazards None required under normal use Memo Memo Page Sharp Corporation