Sharp AL-1650 operation manual Copier TROUBLE?, Self-diagnostic function, Example

Page 51

COPIER TROUBLE?

Problem

Solution

Power is on but copying is not possible.

Lighting fixture flickers.

Is the POWER SAVE ( ) indicator blinking?

Is the indicator on?

Is blinking in the copy quantity display?

Is steadily lit in the copy quantity display?

Is the indicator blinking?

Is the indicator blinking?

Is the START key ( ) indicator blinking?

Is the same power outlet used for the lighting fixture and the copier?

Wait until warm-up is complete.

Warm-up time is approximately 35 seconds.

Copy paper is needed. See page 13, LOADING COPY PAPER.

The TD cartridge is not installed. Install the TD cartridge.

Side cover is open.

Close the front and side covers securely.

The TD cartridge must be replaced. See page

32, TD CARTRIDGE REPLACEMENT.

A misfeed has occurred. See page 36,

MISFEED REMOVAL.

Toner replenishment takes up to 2 minutes.

Wait until the START key ( ) indicator stops blinking.

Connect the copier to a power outlet which is not used for other electric appliances.

Copier trouble?

Be sure to use only genuine SHARP parts and supplies.

Please contact your SHARP service center immediately if a problem persists after checking the above.

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage. An alphanumeric code will appear in the copy quantity display.

Example

Should the copier completely stop and a letter and a number appear alternately, contact your SHARP service center immediately.

GENERAL INFORMATION

49

Image 51
Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions Alarm indicators AUTO/MANUAL/PHOTO / / key and indicators pOriginal Size Enter key and indicators p Paper Size indicators@0 Preset Ratio selector keys and indicators p Dual page Copy key and indicator pLight and dark keys and indicators Auto Image key and indicator pDo not install your copier in areas that are Copier InstallationGetting Started Unpacking Checking Packed Components and AccessoriesInstall the TD cartridge SET-UPGently lift and pull out the paper tray until it stops Store the pressure plate lock which has been removed Turn the power switch on Load copy paperSET-UP Front of the paper trayPush the paper tray firmly back into the copier Loading Copy PaperLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Normal Copying Using the SPFTurn the power switch on Adjust the copy densityPress the Start key Set the number of copies using the two copy quantity KeysStream feeding mode Normal CopyingUsing the original table Normal Copying Enter the number of copies Press the Start key REDUCTION/ENLARGEMENT/ZOOMAutomatic Press the Auto Image KeyManual REDUCTION/ENLARGEMENT/ZOOMUnfold the bypass tray Bypass Feed special paperPress the Tray Select key to select the bypass Bypass Feed special paperTWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display Key Set the number of copies and press the Start key XY ZoomPress the B/W Reverse key Check the copy paper size ReversePress the Dual page Copy key Dual page CopyReplace the original for the interrupted job and press Interrupting a Copy RUNPress the Interrupt key Start key to resume copyingAutomatic Exposure Adjustment Toner Save Mode Press the AUTO/MANUAL/PHOTO Key To select the Manual ModeTo enter the toner save mode, press the light key Genuine Supplies TD Cartridge ReplacementTD Cartridge Replacement To remove it Cartridge out until the green strap handle can be graspedBy the right hand. Lift the cartridge by the handle while Gently install the TD cartridge. To install the TD cartridge Drum Cartridge ReplacementRight feeding roller cover and remove the misfed Misfeed RemovalMisfeed in the SPF First confirm the misfeed locationGently pull the misfed paper out Misfeed RemovalMisfeed in the bypass tray Misfeed in the copierFusing unit is hot. Take care in removing paper Removing itPush gently the right side of the front cover to open Cover On either side of the guide and remove the misfed paper Open the paper guide by pressing down the projectionMisfeed in the upper paper tray Misfeed in the lower paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper List of user programs Setting the user programsEnter a program number using the left copy quantity Key User ProgramsUser Programs Select the desired parameter using the right copy quantityPower Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode Transfer charger User MaintenanceOriginal table and document feeder cover Bypass tray paper feed rollerUser Maintenance Charger cleaner out by holding the tabGently lift and pull out the upper paper tray and take Copier TROUBLE? Problem SolutionSelf-diagnostic function Copier TROUBLE?Example Supply list SuppliesTypes and sizes of copy paper Supply part numbersStore copy paper in the wrapper and lying flat SuppliesGenuine supplies statement Proper storageTurn the power switch off and disconnect the power Cord Moving InstructionsPush the paper tray back into the copier Copier SpecificationsSingle Pass Feeder SpecificationsIndex Index Material Safety Data Sheet Flammable Limits Ignition TemperatureSpecial Fire Fighting Procedure Flash Point Method UsedIngredients CAS No Proportion Other LimitsHealth Hazards None required under normal use Memo Memo Page Sharp Corporation