Sharp AL-1650 operation manual Bypass Feed special paper, Unfold the bypass tray

Page 24

BYPASS FEED (special paper)

The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray.

For special purpose papers, the original image must be smaller than the paper or media for copying.

If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.

Also for standard copy paper, smudges may appear if the copy paper is not at least as large as the original image.

MAKING COPIES Bypass feed (special paper)

1 Unfold the bypass tray.

When feeding 8-1/2" x 14" or 11" x 17" sized paper, extend the bypass tray.

2 Set the paper guides to the copy paper width.

Insert the copy paper (print face down) all the way into

3 the bypass tray.

Up to 100 sheets of standard copy paper measuring from 5-1/2" x 8-1/2" to 11" x 17" can be loaded in the bypass tray.

Transparency film, labels, and other special purpose papers (except envelopes) must be fed individually.

Up to 10 envelopes can be set.

When adding paper, first remove remaining paper, combine it with the paper to be added and then reload as a single stack.

When loading envelopes, make sure that they are straight and flat.

22

Image 24
Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions AUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators pPaper Size indicators Alarm indicatorsDual page Copy key and indicator p Light and dark keys and indicatorsAuto Image key and indicator p @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingInstall the TD cartridge SET-UPGently lift and pull out the paper tray until it stops Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Using the SPF Turn the power switch onAdjust the copy density Normal CopyingSet the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start keyUsing the original table Normal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display Key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment Toner Save Mode Press the AUTO/MANUAL/PHOTO Key To select the Manual ModeTo enter the toner save mode, press the light key TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement To remove it Cartridge out until the green strap handle can be graspedBy the right hand. Lift the cartridge by the handle while Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeMisfeed Removal Misfeed in the SPFFirst confirm the misfeed location Right feeding roller cover and remove the misfedMisfeed Removal Misfeed in the bypass trayMisfeed in the copier Gently pull the misfed paper outFusing unit is hot. Take care in removing paper Removing itPush gently the right side of the front cover to open Cover Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperMisfeed in the upper paper tray Misfeed in the lower paper trayClose the side cover by pressing the handle on the cover Remove the misfed paper Setting the user programs Enter a program number using the left copy quantity KeyUser Programs List of user programsSelect the desired parameter using the right copy quantity User ProgramsPower Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode User Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer chargerUser Maintenance Charger cleaner out by holding the tabGently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE?Self-diagnostic function Copier TROUBLE?Example Supplies Types and sizes of copy paperSupply part numbers Supply listSupplies Genuine supplies statementProper storage Store copy paper in the wrapper and lying flatTurn the power switch off and disconnect the power Cord Moving InstructionsPush the paper tray back into the copier Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsIngredients CAS No Proportion Other LimitsHealth Hazards None required under normal use Memo Memo Page Sharp Corporation