Sharp AL-1650 operation manual User Programs, List of user programs, Setting the user programs

Page 44

User programs

GENERAL INFORMATION

USER PROGRAMS

The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.

		List of user programs
		This copier has the following user programs.

Program No.	Program name	Description

1	Auto clear time	Sets the auto clear time. The copier returns to the initial settings when

		the auto clear time elapses after the last copy is made.

2	Preheat mode	Sets the time that elapses before the copier enters the preheat mode after
		any operation is made. See page 44.

3	Auto power shut-off	Sets the time that elapses before the copier enters the auto power shut-off
	timer	mode after any operation is made. See page 44.

4	Stream feeding mode	Enables or disables the stream feeding mode. For description of the stream
		feeding mode, see page 17.

5	Auto power shut-off	Enables or disables the auto power shut-off mode. See page 44.
	setting

8	Auto paper select mode	Enables or disables the auto paper selection. See page 16.

9	Auto tray switching	Enables or disables the automatic tray switching which occurs when paper
		in a tray runs out. (This switching cannot switch to the bypass tray.)

Setting the user programs

Press and hold the light ( ) key for more than 5

1 seconds until all the alarm indicators ( , , , and ) blink and “– –” appears in the copy quantity display.

Enter a program number using the left copy quantity

2 ( ) key.

● The selected program number will blink in the copy quantity display.

●If a mistake is made in steps 2 to 4, press the CLEAR ( ) key. The copier will return to step 2.

● The program numbers are shown in the table above.

For example, to change the setting of the auto power shut-off timer, enter 3.

42

Image 44

Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions AUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators pPaper Size indicators Alarm indicatorsDual page Copy key and indicator p Light and dark keys and indicatorsAuto Image key and indicator p @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingGently lift and pull out the paper tray until it stops Install the TD cartridgeSET-UP Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Using the SPF Turn the power switch onAdjust the copy density Normal CopyingSet the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start keyUsing the original table Normal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying Press the copy ratio display Key XY ZoomPress the XY-ZOOM key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the AUTO/MANUAL/PHOTO Key To select the Manual Mode TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement By the right hand. Lift the cartridge by the handle while To remove itCartridge out until the green strap handle can be grasped Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeMisfeed Removal Misfeed in the SPFFirst confirm the misfeed location Right feeding roller cover and remove the misfedMisfeed Removal Misfeed in the bypass trayMisfeed in the copier Gently pull the misfed paper outPush gently the right side of the front cover to open Cover Fusing unit is hot. Take care in removing paperRemoving it Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperClose the side cover by pressing the handle on the cover Misfeed in the upper paper trayMisfeed in the lower paper tray Remove the misfed paper Setting the user programs Enter a program number using the left copy quantity KeyUser Programs List of user programsSelect the desired parameter using the right copy quantity User ProgramsAuto power shut-off mode Power Save ModesPreheat mode Copying from the preheat mode Power Save ModesSetting the power save modes User Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer chargerGently lift and pull out the upper paper tray and take User MaintenanceCharger cleaner out by holding the tab Problem Solution Copier TROUBLE?Example Self-diagnostic functionCopier TROUBLE? Supplies Types and sizes of copy paperSupply part numbers Supply listSupplies Genuine supplies statementProper storage Store copy paper in the wrapper and lying flatPush the paper tray back into the copier Turn the power switch off and disconnect the power CordMoving Instructions Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsHealth Hazards Ingredients CAS No ProportionOther Limits None required under normal use Memo Memo Page Sharp Corporation