Sharp AL-1650 operation manual Using the original table

Page 20

MAKING COPIES

NORMAL COPYING

Using the original table

 

1

Turn the power switch on.

 

Power on

It will take about 35 seconds for the copier to warm up. However, you

 

 

can make desired settings and press the START (

) key during

 

 

warm-up. Copying will start after warm-up.

 

Place an original face down on the original table, and

2 align it with the original size scale.

Normal copying

3 Close the document feeder cover.

Ensure that the copy paper size in the paper tray is the

4 same size as the original.

Use the ORIGINAL SIZE ENTER () key to select the original size. Copy paper of the same size as the original will be automatically

selected. If desired, the other paper tray can be selected by pressing the

TRAY SELECT ( ) key.

If no tray contains the required paper size, place the required paper into

the bypass tray and use the TRAY SELECT ( ) key to select the bypass tray.

The bypass tray cannot be selected automatically.

5

Adjust the copy density.

 

 

 

This copier has three exposure modes to choose from — AUTOMATIC

 

 

 

(

), MANUAL (

 

), and PHOTO (

).

 

 

Automatic exposure is the standard initial setting for this copier. In this

 

 

mode, the characteristics of the original are “read” by the exposure

 

 

system and adjustments are automatically made. This optimizes the

 

 

contrast of the copied images by reducing the effect of colored or

 

 

shaded background areas. See page 30 to adjust the automatic exposure

 

 

level.

 

 

 

 

 

 

 

 

For manual copy density adjustment, press the AUTO/MANUAL/

 

 

PHOTO (

/

/

) key to select MANUAL (

) and

 

 

adjust with the light (

 

) and dark (

) keys as desired.

 

18

Image 20
Contents AL-1650 For Your Protection Contents Safety Precautions Main Features Part Names and Functions Part Names and Functions AUTO/MANUAL/PHOTO / / key and indicators p Original Size Enter key and indicators pPaper Size indicators Alarm indicatorsDual page Copy key and indicator p Light and dark keys and indicatorsAuto Image key and indicator p @0 Preset Ratio selector keys and indicators pCopier Installation Do not install your copier in areas that areGetting Started Checking Packed Components and Accessories UnpackingGently lift and pull out the paper tray until it stops Install the TD cartridgeSET-UP Turn the power switch on Load copy paper SET-UPFront of the paper tray Store the pressure plate lock which has been removedLoading Copy Paper Push the paper tray firmly back into the copierLoading Copy Paper Press the Start key and then the Paper Size 11ENTER key Using the SPF Turn the power switch onAdjust the copy density Normal CopyingSet the number of copies using the two copy quantity Keys Stream feeding modeNormal Copying Press the Start keyUsing the original table Normal Copying REDUCTION/ENLARGEMENT/ZOOM AutomaticPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualBypass Feed special paper Unfold the bypass trayBypass Feed special paper Press the Tray Select key to select the bypassTWO-SIDED Copying Press the copy ratio display Key XY ZoomPress the XY-ZOOM key XY Zoom Set the number of copies and press the Start keyReverse Press the B/W Reverse key Check the copy paper sizeDual page Copy Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Replace the original for the interrupted job and pressAutomatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the AUTO/MANUAL/PHOTO Key To select the Manual Mode TD Cartridge Replacement Genuine SuppliesTD Cartridge Replacement By the right hand. Lift the cartridge by the handle while To remove itCartridge out until the green strap handle can be grasped Drum Cartridge Replacement Gently install the TD cartridge. To install the TD cartridgeMisfeed Removal Misfeed in the SPFFirst confirm the misfeed location Right feeding roller cover and remove the misfedMisfeed Removal Misfeed in the bypass trayMisfeed in the copier Gently pull the misfed paper outPush gently the right side of the front cover to open Cover Fusing unit is hot. Take care in removing paperRemoving it Open the paper guide by pressing down the projection On either side of the guide and remove the misfed paperClose the side cover by pressing the handle on the cover Misfeed in the upper paper trayMisfeed in the lower paper tray Remove the misfed paper Setting the user programs Enter a program number using the left copy quantity KeyUser Programs List of user programsSelect the desired parameter using the right copy quantity User ProgramsAuto power shut-off mode Power Save ModesPreheat mode Copying from the preheat mode Power Save ModesSetting the power save modes User Maintenance Original table and document feeder coverBypass tray paper feed roller Transfer chargerGently lift and pull out the upper paper tray and take User MaintenanceCharger cleaner out by holding the tab Problem Solution Copier TROUBLE?Example Self-diagnostic functionCopier TROUBLE? Supplies Types and sizes of copy paperSupply part numbers Supply listSupplies Genuine supplies statementProper storage Store copy paper in the wrapper and lying flatPush the paper tray back into the copier Turn the power switch off and disconnect the power CordMoving Instructions Specifications CopierSpecifications Single Pass FeederIndex Index Material Safety Data Sheet Ignition Temperature Special Fire Fighting ProcedureFlash Point Method Used Flammable LimitsHealth Hazards Ingredients CAS No ProportionOther Limits None required under normal use Memo Memo Page Sharp Corporation