Misfeed in the transport area, Close the side cover

Sharp AR-M160, AR-M205 operation manual Misfeed in the transport area, Close the side cover

Page 69

TROUBLESHOOTING

C. Misfeed in the transport area

1 Open the fusing paper guide by pressing down the projection on either side of the guide and remove the misfed paper.

Be careful not to tear the misfed paper during removal.

Warning

The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or injury.

2 If the misfed paper cannot be removed by the previous step but is visible in the paper output area, remove the paper by pulling it into the paper output area.

Be careful not to tear the misfed paper during removal.

3 Close the side cover.

The misfeed indicator ( ) will go out.

• When closing the side cover, press on the

Note handle.

•If the paper was torn, make sure that no torn pieces remain in the machine.

•If the misfeed indicator ( ) does not stop blinking, check for torn pieces of paper in the machine.

Image 69

Contents

AR-M205 AR-M160For Your Records Contents User Settings Do not install your machine in areas that are Important Points When Selecting AN Installation SiteChanges, e.g., near an Air conditioner orTrademark acknowledgements Safety precautionsDo not touch the photoconductive drum green portion Scratches or smudges on the drum will cause dirty copiesOnline Manual on the accessory CD-ROM Using the ManualSoftware Setup Guide separate manual Environmental InformationSPF and Rspf Differences Between Models Conventions Used in this ManualMain Features Part Names and Functions Before Using the Machine Operation Panel Zoom indicator Power Save indicatorOriginal Size Enter key/ORIGINAL Size indicators Paper Size indicatorsPower on Power on and OFFPower OFF Power Save ModesLoading Paper Paper tray type Paper type Size Weight CapacityPaper Special papersLoading the paper tray Loading PaperLocks in place Fan the paperImportant points when inserting paper in the bypass tray Loading the bypass traySet the paper guides to the copy paper width Follow these steps to change a tray’s paper size setting Changing a TRAY’S Paper Size SettingIndicator EnvelopesPress the Start key and then the Paper Size Enter key Important points when using the printer modeNormal Copying Copying from the document glassClose the document cover/SPF/RSPF Set the originals face up in the document feeder tray Copying from the SPF/RSPFSet the number of copies Copy FunctionsStream feeding mode Auto paper select modeRemoving the document cover Originals that can be used in the SPF/RSPFMaking a Copy Darker or Lighter Auto tray switchingSelecting the Tray Original typesImportant note when making a large number of copies Setting the Number of CopiesREDUCTION/ENLARGMENT/ZOOM Automatic Ratio SelectionFine adjustment of the ratio Selecting a preset ratioManual Ratio Selection Press the Auto Image keyPress the Copy ratio display key XY Zoom copyingNumber of copies display TWO-SIDED Copying Using the Bypass Tray Copy original aPlace original B as shown below Rspf Automatic TWO-SIDED CopyingUsing the Rspf Using the document glassPress the Start key Place originals in the RSPF. p.19Press a numeric key to enter Setting code Press the Original to Copy key to exit the settingImage Rotation in Duplex Copying Original Copy 2 x 11 paper is used for dual page copying Dual page CopyingInterrupting a Copy RUN Press the Interrupt key to interrupt the copy runReplace the previous originals and press the Start key Sort Copy / Group Copy Rotating the Image 90 DegreesPress the SORT/GROUP key to select the desired mode Using the SPF/RSPFIf the memory becomes full If the paper output tray becomes fullMode is selected Using 2 in 1 / 4 in 1 copy in combination with sort copyCopying Multiple Originals Onto a Single Sheet of Paper Order 2 in 1, 4Use the 2 in 1 / 4 in 1 key to access the setting Setting the layout patternSelect the setting code by pressing a numeric key Press the 2 in 1 / 4 in 1 key to exit the settingSelect the location of the margin AR-M205 only Creating Margins When CopyingPlace the originals Press the 1 key or the 2 key, and then press the Start keyErasing Shadows around the Edges of a Copy Press the Erase key to select the desired erase modePRINTER/SCANNER Functions System requirements for USB 2.0 Hi-Speed modeBasic Procedure for Printing Using the Printer ModePausing a print job When Use close paper size is disabledUsing the Scanner Mode Scanning Using the Keys on the MachinePress the Scan key Press a Scan Menu key to begin Scanning Operation in COPY, PRINTER, and Scanner Modes Scan Menu keys and the Button Manager scan menuPRINTER/SCANNER Functions Press the AUTO/TEXT/PHOTO key to complete the setting Adjusting the Automatic Exposure LevelWhen enabling toner Enabling Toner Save ModePhoto indicator stops blinking and lights steadily Save mode, make sureUser Programs Customizing SettingsPattern User SettingsLeft edge 300dpiAuto Base settings Selecting a Setting for a User ProgramPress the Light key to complete the settings Enter the program number withSettings for Auditing Mode Auditing ModeAuditing Mode Settings Enter the program number with the numeric keys Selecting Auditing Mode SettingsAccount number entry Auditing modeAccount number change Account number deletionCopying when Auditing mode is enabled Resetting accountThis chapter describes troubleshooting and misfeed removal TroubleshootingAny of the alarm indicator Machine does not print. on Line indicator does not blinkMACHINE/COPYING Problems Paper is outside of the specified size and weight Range Problem Cause and solution Misfeed occurPaper curled or damp Paper is not loaded properlyDisplay or the Original Data indicator is blinking Problem Cause and solution Copying or printing is performedAny other indicators are lit Be set An interrupt copy job is in progressPrinting and Scanning Problems Runs off the paper Printed image is dirtyCorrectly and gaps appear Lines in tables are not alignedBrightness and contrast settings are not suitable You have not specified a suitable resolutionPoor scanning quality Quick Scan has been selectedThere is not enough computer memory You do not have Administrator rightsRemoving the software What to do when a notice page is printedClick the start button, and then click Control Panel Click Add or Remove ProgramsIndicators and Display Messages Misfeed in the SPF/RSPF Misfeed RemovalRemove the misfed original Section aMisfeed indicator will go out Misfeed in the Bypass TraySection C Misfeed in the paper feed area Misfeed in the MachineClose the front cover and side cover Be careful not to tearMisfeed in the fusing area Misfeed in the transport area Close the side coverBe careful not to tear the misfed paper during removal Misfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Remove the misfed paper Open the lower side coverClose the lower side cover Close the lower paper trayReplacing the Toner Cartridge Toner cartridge replacement required indicator will go outClose the front cover Discard the shutterChecking the Total Output Count Checking the Total Output Count and Toner LevelTotal output count Total copy countCleaning the Document Glass and SPF/RSPF/DOCUMENT Cover Routine MaintenanceDo not spray flammable cleaner gas Checking the Toner LevelCleaning the Transfer Charger Cleaning the Bypass Tray Paper Feed RollerReturn the charger cleaner to its Original position. Close the upperPeripheral Devices Option that can be installed On the AR-M205 On the AR-M160Single Pass Feeder Reversing Single Pass Feeder SpecificationsSheet Paper Feed Unit 250-SHEET Paper Feed Unit Part namesStorage of Supplies SpecificationDual Function Board Proper StorageSpecifications Printer Function AppendixRAL-UZ62 Scanner Function Software License Page Supplier Identification Sharp Corporation Product NameSubstance PreparationX Ingredient CAS No Proportion Osha PELEnvironmental Precautions Personal PrecautionsMethods for Cleaning Up Most Important Hazards and Effects of the ProductsPersonal Protective Equipment Exposure limit valuesBoiling/Melting Point Softening Point CNo data are available 4/4Osha PEL Acgih TLV MAK-TWA NOHSC-TWA AR-202ND / AR-202DV / AR-202SD / AR-202SD-C Black DeveloperData Issued Jun Msds No. F-31211 Physical and Chemical Properties Ecological Information Index 10, 62 Preset Ratio selector indicator11, 62 Misfeed removalProblem occurs Machine settingsIndicators, lit and blinking Index by PurposePage Sharp Corporation

Related manuals

Sharp AR-M160, AR-M205 operation manual Misfeed in the transport area, Close the side cover

C. Misfeed in the transport area

Be careful not to tear the misfed paper during removal.

3 Close the side cover.

The misfeed indicator ( ) will go out.