Sharp AR-207 operation manual Normal Copying, Power on, One-sided copies from one-sided originals

Page 16

NORMAL COPYING

MAKING COPIES

This copier has two document input stations –– a reversing single pass feeder (RSPF) for automatic document feeding and an original table for manual handling of bound documents. The RSPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2" to 11" x 17" and in the weight range of 15 to 24 lbs.

Be sure to remove any staples or paper clips from the originals.

Damaged or crumpled originals may misfeed in the RSPF. It is recommended that these originals be copied from the original table.

Before placing curled or wavy originals into the document feeder tray, be sure to flatten them. If not, original misfeeds may result.

For best feeding of originals which have binding holes punched into them, insert them so that the holes are

positioned to the right or along the side guides. In this case the settings for location of margin and image rotation in duplex copying may need to be changed to ensure the images are produced in the desired orientation. See pages 22 and 41.

Special originals such as transparency film and tracing paper should not be fed through the RSPF but should be copied from the original table.

The bypass tray and any tray with non-standard size paper cannot be used in the duplex copy mode.

Paper sizes that can be used in the duplex mode are 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17".

If the offset stack mode is enabled using user program No. 19, each set of copies will be offset from the previous set in the sort and group modes.

Normal copying

Stream feeding mode

If the stream feeding mode has been enabled using user program No. 4, the RSPF indicator will continue to blink for approximately 5 seconds after feeding of all originals is completed. While this indicator is blinking, any new originals placed in the RSPF will be fed and copied automatically. See page 51, USER PROGRAMS.

Power on

 

1

Turn the power switch on.

Power on

It will take about 35 seconds for the copier to warm up.

 

 

However, you can make desired settings and press the START key

 

 

during warm-up. Copying will start after warm-up.

 

 

If the copier has been programmed in the auditing mode, the START

 

 

key indicator will not light up and “ ––– will appear in the copy

 

 

quantity display. Enter an assigned 3-digit account number. See page

 

 

13.

If an optional printer expansion kit or facsimile expansion kit is installed, when the power is already on and all indicators except the POWER SAVE indicator are off, the copier is in the auto power shut- off mode. Press the START key in this case. See page 58, POWER SAVE MODES.

One-sided copies from one-sided originals

1 Ensure that no original is left on the original table.

2 Adjust the original guides to the size of the originals.

Set the originals face up in the document feeder tray.

3

The RSPF indicator will light up. If this indicator does not light up, the

 

originals are not properly set, or the RSPF is not properly closed.

14

Image 16
Contents AR-207 Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Interrupt key and indicator p Zoom indicator p.24Paper Size indicators Alarm indicatorsStart key and indicator Preset Ratio selector keys and indicatorsOriginal Size Enter key and indicators Auto Paper Select indicatorDo not install your copier in areas that are Copier InstallationAlso make certain the outlet is properly grounded Do not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Enter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Power on Turn the power switch onStream feeding mode Normal CopyingEnsure that the one-sided to one-sided copying mode is Adjust the copy densityNormal Copying Set the number of copies using the numeric keys Two-sided copies from one-sided originalsPress the Start key Ensure that no original is left on the original tableSet the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder trayClose the document feeder cover Ensure that the desired paper tray is selectedCopying from the Original Table Copying from the original table Select the desired parameter using the numeric keys Setting image rotation in duplex copyingPress the Original to Copy key REDUCTION/ENLARGEMENT/ZOOM AutomaticREDUCTION/ENLARGEMENT/ZOOM ManualRatio, then press To increase the ratioBypass Feed special paper Unfold the bypass trayBypass Feed special paper Sort mode Group modeSORT/GROUP Offset stackSORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display keyUse the Preset Ratio selector , keys and zoom XY ZoomReverse Press the Dual page Copy key Dual page CopyPlace the originals on the original table with the center Rotation Copying 2 x 11 is performed, the image cannot be rotated1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selectionErase Press the Erase key to select the desired erase modeEnsure that the desired copy paper size is selected Erase Until the Margin Shift indicator will blink Margin ShiftPlace the original in the document feeder tray or on To confirm or set the location of the margin, pressToner Cartridge Replacement Push the toner cartridge lock release lever and pullToner Cartridge Replacement Toner cartridge lifeThan 5 seconds Press the light keyMisfeed in the Rspf First confirm the misfeed locationMisfeed Removal Misfeed in the bypass trayMisfeed in the copier If the misfed original cannot be removed in steps 1Removing it Push gently on both sides of the front cover to open CoverTurn the roller rotating knob in the direction ArrowMisfeed in the upper paper tray Close the side cover by pressing the handle on CoverMisfeed in the lower paper tray Pull out the lower paper tray and remove the misfed paperClose the paper tray Close the lower side cover If the misfed paper is not seen in , gently liftMaintenance Required Developer RequiredList of user programs User ProgramsProgram Program name Description Setting the user programs Enter a program number using the numeric keysUser Programs Program name Program NoTo continue with other user programs, press the key Select the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Number to be changed Use the copy ratio display key to select the accountUse the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode Copying from the auto power shut-off modeUser Maintenance Bypass tray with a soft, clean cloth dampened withOriginal table and document feeder cover Bypass tray paper feed rollerUser Maintenance Transfer charger cleaningCharger cleaner out by holding the tab Gently lift and pull out the upper paper tray and takeProblem Solution Copier TROUBLE?Copier TROUBLE? ProblemCOPY/FAX key Self-diagnostic function ExampleSupplies Types and sizes of copy paperSupplies Genuine supplies statementProper storage Store the supplies in a location that isSpecifications RspfSpecifications Reversing Single Pass FeederOptional Equipment System Configuration Part Names Loading copy paperMisfeed removal Specifications AR-DE5Index Index Material Safety Data Sheet Emergency and First Aid ProceduresProduct Routes of EntryIgnition Temperature Special Fire Fighting ProcedureSpecific Gravity Vapor Pressure Vapor DensityIngredients ProportionHealth Hazards Medical Conditions Generally Aggravated by ExposureEvaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor OdorlessMemo For users in the USA Sharp Corporation