Sharp AR-207 operation manual Select the desired parameter using the numeric keys

Page 55

USER PROGRAMS

4	Select the desired parameter using the numeric keys.
	● The entered parameter number will blink on the right side of the copy

quantity display.

● The parameters are shown in the table below.

For example, to change the setting of the auto power shut-off timer to 60 min., press key 2.

Program name

Parameters

Auto clear time

0

OFF

1

30 sec.

* 2

60 sec.

3

90 sec.

4

120 sec.

5

10 sec.

Preheat mode

0

OFF

1

30 sec.

2

60 sec.

* 3

90 sec.

4

120 sec.

Auto power shut-off timer

* 1

30 min.

2

60 min.

3

90 min.

4

120 min.

5

240 min.

Stream feeding mode

* 0

OFF

1

ON

Auto power shut-off setting

0

OFF

* 1

ON

Border line for 2 in 1 or 4 in 1

* 0

OFF

1

ON

Rotation copy

0

OFF

* 1

ON

Auto paper select mode

0

OFF

* 1

ON

Auto tray switching

0

OFF

* 1

ON

Erase width adjustment

0

0"

1

1/4"

* 2

1/2"

3

3/4"

4

1"

Layout in 2 in 1 copy

* 1

Pattern 1

2

Pattern 2

Layout in 4 in 1 copy

* 1

Pattern 1

2

Pattern 2

3

Pattern 3

4

Pattern 4

Offset of paper output tray

0

Upper OFF, lower OFF

* 1

Upper ON, lower ON

2

Upper ON, lower OFF

3

Upper OFF, lower ON

Image rotation in duplex

* 0

OFF

1

ON

copying

Location of the margin

* 1

Left

2

Top

Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 37.

If you select “0” (OFF) in a program, the corresponding

function will be disabled.

5	Press the START key.
	● The right-hand number in the copy quantity display will be steadily lit

and the entered value will be stored.

GENERAL INFORMATION

To continue with other user programs, press the key

6 and then repeat steps 2 to 5. To exit the user program mode, press the light () key.

●All the alarm indicators will go out.

User programs

53

Image 55

Contents AR-207 Safety Precautions Contents Conventions used in this manual IntroductionMain Features Part Names and Functions Part Names and Functions Alarm indicators Interrupt key and indicator pZoom indicator p.24 Paper Size indicatorsAuto Paper Select indicator Start key and indicatorPreset Ratio selector keys and indicators Original Size Enter key and indicatorsDo not install your copier in areas that are Copier InstallationAlso make certain the outlet is properly grounded Do not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Enter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Normal Copying Power onTurn the power switch on Stream feeding modeEnsure that the one-sided to one-sided copying mode is Adjust the copy densityNormal Copying Ensure that no original is left on the original table Set the number of copies using the numeric keysTwo-sided copies from one-sided originals Press the Start keySet the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key Original has been set in the document feeder tray One-sided copies from two-sided originalsEnsure that the desired paper tray is selected Close the document feeder coverCopying from the Original Table Copying from the original table Select the desired parameter using the numeric keys Setting image rotation in duplex copyingPress the Original to Copy key Automatic REDUCTION/ENLARGEMENT/ZOOMTo increase the ratio REDUCTION/ENLARGEMENT/ZOOMManual Ratio, then pressUnfold the bypass tray Bypass Feed special paperBypass Feed special paper Offset stack Sort modeGroup mode SORT/GROUPSORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN Automatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the copy ratio display key XY ZoomXY Zoom Use the Preset Ratio selector , keys and zoomReverse Press the Dual page Copy key Dual page CopyPlace the originals on the original table with the center 2 x 11 is performed, the image cannot be rotated Rotation Copying1 or 4 Press the 2 in 1 / 4 in 1 key to complete the selection Enter the desired pattern number using a numeric keyErase Press the Erase key to select the desired erase modeEnsure that the desired copy paper size is selected Erase To confirm or set the location of the margin, press Until the Margin Shift indicator will blinkMargin Shift Place the original in the document feeder tray or onPush the toner cartridge lock release lever and pull Toner Cartridge ReplacementPress the light key Toner Cartridge ReplacementToner cartridge life Than 5 secondsFirst confirm the misfeed location Misfeed in the RspfIf the misfed original cannot be removed in steps 1 Misfeed RemovalMisfeed in the bypass tray Misfeed in the copierPush gently on both sides of the front cover to open Cover Removing itArrow Turn the roller rotating knob in the directionClose the side cover by pressing the handle on Cover Misfeed in the upper paper trayIf the misfed paper is not seen in , gently lift Misfeed in the lower paper trayPull out the lower paper tray and remove the misfed paper Close the paper tray Close the lower side coverDeveloper Required Maintenance RequiredList of user programs User ProgramsProgram Program name Description Program name Program No Setting the user programsEnter a program number using the numeric keys User ProgramsTo continue with other user programs, press the key Select the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Use the copy ratio display key to select the account Number to be changedPress and hold down the 0 key Use the copy ratio display key to select the account NumberProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Copying from the auto power shut-off mode Power Save ModesSetting the power save modes Copying from the preheat modeBypass tray paper feed roller User MaintenanceBypass tray with a soft, clean cloth dampened with Original table and document feeder coverGently lift and pull out the upper paper tray and take User MaintenanceTransfer charger cleaning Charger cleaner out by holding the tabCopier TROUBLE? Problem SolutionCopier TROUBLE? ProblemCOPY/FAX key Example Self-diagnostic functionTypes and sizes of copy paper SuppliesStore the supplies in a location that is SuppliesGenuine supplies statement Proper storageRspf SpecificationsReversing Single Pass Feeder SpecificationsOptional Equipment System Configuration Loading copy paper Part NamesMisfeed removal AR-DE5 SpecificationsIndex Index Routes of Entry Material Safety Data SheetEmergency and First Aid Procedures ProductVapor Density Ignition TemperatureSpecial Fire Fighting Procedure Specific Gravity Vapor PressureMedical Conditions Generally Aggravated by Exposure IngredientsProportion Health HazardsAppearance Fine powder Color Black Odor Odorless Evaporation Rate Not applicable ViscosityMemo For users in the USA Sharp Corporation