Sharp AR-207 operation manual Safety Precautions

Page 2

	➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
➢				➢
➣				➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢	FOR YOUR RECORDS ...			➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
	FOR YOUR RECORDS ...
	To protect against loss or theft, record and retain for reference the
	copier’s serial number located on the back of the unit.
	Model Number	AR-207
	Serial Number
	Date of Purchase
	Place of Purchase
	Authorized Sharp Copier
	Service Department Number
➢				➢
	➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣

CAUTIONS

Follow the cautions below when using this copier.

●The fusing area is hot. Exercise care in this area when removing misfed paper.

●Do not look directly at the light source. Doing so may damage your eyes.

●The socket-outlet shall be installed near the equipment and shall be easily accessible.

●Place the copier on a firm, level surface.

●Do not install the copier in a humid or dusty location.

●When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

●When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet.

●Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the copier.

●Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

SAFETY PRECAUTIONS

This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the copier does not produce hazardous laser radiation. For your safety, observe the precautions below.

●Do not remove the cabinet, operation panel or any other covers.

●The copier’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by

inserting wedges or other items into switch slots.

Image 2

Contents AR-207 Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.24 Alarm indicatorsOriginal Size Enter key and indicators Start key and indicatorPreset Ratio selector keys and indicators Auto Paper Select indicatorAlso make certain the outlet is properly grounded Copier InstallationDo not install your copier in areas that are Do not touch the photoconductive drum green portion Push the paper tray firmly back into the copier Loading Copy PaperGently lift and pull out the paper tray until it stops Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Auditing Accounts When copying is completed, press the Audit Clear KeyEnter your account number using the numeric keys Stream feeding mode Power onTurn the power switch on Normal CopyingNormal Copying Adjust the copy densityEnsure that the one-sided to one-sided copying mode is Press the Start key Set the number of copies using the numeric keysTwo-sided copies from one-sided originals Ensure that no original is left on the original tableSet the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder trayClose the document feeder cover Ensure that the desired paper tray is selectedCopying from the Original Table Copying from the original table Press the Original to Copy key Setting image rotation in duplex copyingSelect the desired parameter using the numeric keys REDUCTION/ENLARGEMENT/ZOOM AutomaticRatio, then press REDUCTION/ENLARGEMENT/ZOOMManual To increase the ratioBypass Feed special paper Unfold the bypass trayBypass Feed special paper SORT/GROUP Sort modeGroup mode Offset stackSet the originals face up in the document feeder tray Copying in the sort modeSORT/GROUP Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display keyUse the Preset Ratio selector , keys and zoom XY ZoomReverse Place the originals on the original table with the center Dual page CopyPress the Dual page Copy key Rotation Copying 2 x 11 is performed, the image cannot be rotated1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selectionEnsure that the desired copy paper size is selected Press the Erase key to select the desired erase modeErase Erase Place the original in the document feeder tray or on Until the Margin Shift indicator will blinkMargin Shift To confirm or set the location of the margin, pressToner Cartridge Replacement Push the toner cartridge lock release lever and pullThan 5 seconds Toner Cartridge ReplacementToner cartridge life Press the light keyMisfeed in the Rspf First confirm the misfeed locationMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray If the misfed original cannot be removed in steps 1Removing it Push gently on both sides of the front cover to open CoverTurn the roller rotating knob in the direction ArrowMisfeed in the upper paper tray Close the side cover by pressing the handle on CoverClose the paper tray Close the lower side cover Misfeed in the lower paper trayPull out the lower paper tray and remove the misfed paper If the misfed paper is not seen in , gently liftMaintenance Required Developer RequiredProgram Program name Description User ProgramsList of user programs User Programs Setting the user programsEnter a program number using the numeric keys Program name Program NoTo continue with other user programs, press the key Enter a 3-digit account number using the numeric keys Settings for auditing accountsSelect the desired setting using the numeric keys Number to be changed Use the copy ratio display key to select the accountUse the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Auto power shut-off mode Power Save ModesPreheat mode Copying from the preheat mode Power Save ModesSetting the power save modes Copying from the auto power shut-off modeOriginal table and document feeder cover User MaintenanceBypass tray with a soft, clean cloth dampened with Bypass tray paper feed rollerCharger cleaner out by holding the tab User MaintenanceTransfer charger cleaning Gently lift and pull out the upper paper tray and takeProblem Solution Copier TROUBLE?COPY/FAX key ProblemCopier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperProper storage SuppliesGenuine supplies statement Store the supplies in a location that isSpecifications RspfSpecifications Reversing Single Pass FeederOptional Equipment System Configuration Part Names Loading copy paperMisfeed removal Specifications AR-DE5Index Index Product Material Safety Data SheetEmergency and First Aid Procedures Routes of EntrySpecific Gravity Vapor Pressure Ignition TemperatureSpecial Fire Fighting Procedure Vapor DensityHealth Hazards IngredientsProportion Medical Conditions Generally Aggravated by ExposureEvaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor OdorlessMemo For users in the USA Sharp Corporation