Sharp AR-207 operation manual Automatic Exposure Adjustment

Page 32

AUTOMATIC EXPOSURE ADJUSTMENT

The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the RSPF respectively. To set the level for the RSPF, place an original in the document feeder tray and make sure that the RSPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the RSPF indicator does not light up.

MAKING COPIESAutomatic exposure adjustment

1

2

Press the AUTO/MANUAL/PHOTO key to select the PHOTO mode.

Press and hold down the AUTO/MANUAL/PHOTO key for approximately 5 seconds.

●The PHOTO indicator will go out and the AUTO indicator will begin to blink.

●One or two exposure indicators corresponding to the current auto- matic exposure level will light up. The factory default setting is level “3”.

3

4

Press the light () or dark () key to lighten or darken the automatic exposure level as desired.

Press the AUTO/MANUAL/PHOTO key.

●The AUTO indicator will stop blinking and will light up steadily.

●This automatic exposure level will remain in effect until you change it again by this procedure.

30

Image 32

Contents AR-207 Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Interrupt key and indicator p Zoom indicator p.24Paper Size indicators Alarm indicatorsStart key and indicator Preset Ratio selector keys and indicatorsOriginal Size Enter key and indicators Auto Paper Select indicatorAlso make certain the outlet is properly grounded Copier InstallationDo not install your copier in areas that are Do not touch the photoconductive drum green portion Push the paper tray firmly back into the copier Loading Copy PaperGently lift and pull out the paper tray until it stops Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Auditing Accounts When copying is completed, press the Audit Clear KeyEnter your account number using the numeric keys Power on Turn the power switch onStream feeding mode Normal CopyingNormal Copying Adjust the copy densityEnsure that the one-sided to one-sided copying mode is Set the number of copies using the numeric keys Two-sided copies from one-sided originalsPress the Start key Ensure that no original is left on the original tableSet the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder trayClose the document feeder cover Ensure that the desired paper tray is selectedCopying from the Original Table Copying from the original table Press the Original to Copy key Setting image rotation in duplex copyingSelect the desired parameter using the numeric keys REDUCTION/ENLARGEMENT/ZOOM AutomaticREDUCTION/ENLARGEMENT/ZOOM ManualRatio, then press To increase the ratioBypass Feed special paper Unfold the bypass trayBypass Feed special paper Sort mode Group modeSORT/GROUP Offset stackSet the originals face up in the document feeder tray Copying in the sort modeSORT/GROUP Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display keyUse the Preset Ratio selector , keys and zoom XY ZoomReverse Place the originals on the original table with the center Dual page CopyPress the Dual page Copy key Rotation Copying 2 x 11 is performed, the image cannot be rotated1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selectionEnsure that the desired copy paper size is selected Press the Erase key to select the desired erase modeErase Erase Until the Margin Shift indicator will blink Margin ShiftPlace the original in the document feeder tray or on To confirm or set the location of the margin, pressToner Cartridge Replacement Push the toner cartridge lock release lever and pullToner Cartridge Replacement Toner cartridge lifeThan 5 seconds Press the light keyMisfeed in the Rspf First confirm the misfeed locationMisfeed Removal Misfeed in the bypass trayMisfeed in the copier If the misfed original cannot be removed in steps 1Removing it Push gently on both sides of the front cover to open CoverTurn the roller rotating knob in the direction ArrowMisfeed in the upper paper tray Close the side cover by pressing the handle on CoverMisfeed in the lower paper tray Pull out the lower paper tray and remove the misfed paperClose the paper tray Close the lower side cover If the misfed paper is not seen in , gently liftMaintenance Required Developer RequiredProgram Program name Description User ProgramsList of user programs Setting the user programs Enter a program number using the numeric keysUser Programs Program name Program NoTo continue with other user programs, press the key Enter a 3-digit account number using the numeric keys Settings for auditing accountsSelect the desired setting using the numeric keys Number to be changed Use the copy ratio display key to select the accountUse the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Auto power shut-off mode Power Save ModesPreheat mode Power Save Modes Setting the power save modesCopying from the preheat mode Copying from the auto power shut-off modeUser Maintenance Bypass tray with a soft, clean cloth dampened withOriginal table and document feeder cover Bypass tray paper feed rollerUser Maintenance Transfer charger cleaningCharger cleaner out by holding the tab Gently lift and pull out the upper paper tray and takeProblem Solution Copier TROUBLE?COPY/FAX key ProblemCopier TROUBLE? Self-diagnostic function ExampleSupplies Types and sizes of copy paperSupplies Genuine supplies statementProper storage Store the supplies in a location that isSpecifications RspfSpecifications Reversing Single Pass FeederOptional Equipment System Configuration Part Names Loading copy paperMisfeed removal Specifications AR-DE5Index Index Material Safety Data Sheet Emergency and First Aid ProceduresProduct Routes of EntryIgnition Temperature Special Fire Fighting ProcedureSpecific Gravity Vapor Pressure Vapor DensityIngredients ProportionHealth Hazards Medical Conditions Generally Aggravated by ExposureEvaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor OdorlessMemo For users in the USA Sharp Corporation