Sharp AR-207 operation manual Power Save Modes, Preheat mode, Auto power shut-off mode

Page 60

POWER SAVE MODES

The copier has two power save modes to reduce overall power consumption thereby reducing the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode.

●User programs

The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode. These times can be changed using user programs. It is suggested that you set appropriate times according to the actual usage of the copier. See page 51.

GENERAL INFORMATION Power save modes

Preheat mode

When the copier enters the preheat mode, the POWER SAVE indicator will light up and other indicators will remain on or off as before. In this condition, the fuser in the copier is maintained at a lower heat level, thereby saving power. The preheat level is, however, high enough to allow the copier to come to a ready condition or begin copying within 10 seconds after any key input or copier operation such as paper tray operation is performed.

Auto power shut-off mode

If the auto power shut-off mode is enabled, the copier will automatically turn off the power once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or the power is first turned on. The power switch will automatically be turned to the “OFF” position.

To turn the power back on, simply turn the power switch to the “ON” position.

●If an optional printer expansion kit or facsimile expansion kit is installed and this mode is enabled, the POWER SAVE indicator will light up and all other indicators will go out. The auto power shut-off mode saves more power but requires a longer time to warm up before copying can begin.

As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

The Environmental Choice Program guidelines are applied to the products only in Canada. The products that meet the Environmental Choice Program guidelines carry the logo shown to the left. The products without the logo may not meet the Environmental Choice Program guidelines.

58

Page 59 Page 61
Image 60
Page 59 Page 61
Contents AR-207 Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Interrupt key and indicator p Zoom indicator p.24Paper Size indicators Alarm indicatorsStart key and indicator Preset Ratio selector keys and indicatorsOriginal Size Enter key and indicators Auto Paper Select indicatorCopier Installation Do not install your copier in areas that areAlso make certain the outlet is properly grounded Do not touch the photoconductive drum green portion Loading Copy Paper Gently lift and pull out the paper tray until it stopsPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key When copying is completed, press the Audit Clear Key Enter your account number using the numeric keysAuditing Accounts Power on Turn the power switch onStream feeding mode Normal CopyingAdjust the copy density Ensure that the one-sided to one-sided copying mode isNormal Copying Set the number of copies using the numeric keys Two-sided copies from one-sided originalsPress the Start key Ensure that no original is left on the original tableTwo-sided copies from two-sided originals Set the number of copies and press the Start keySet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder trayClose the document feeder cover Ensure that the desired paper tray is selectedCopying from the Original Table Copying from the original table Setting image rotation in duplex copying Select the desired parameter using the numeric keysPress the Original to Copy key REDUCTION/ENLARGEMENT/ZOOM AutomaticREDUCTION/ENLARGEMENT/ZOOM ManualRatio, then press To increase the ratioBypass Feed special paper Unfold the bypass trayBypass Feed special paper Sort mode Group modeSORT/GROUP Offset stackCopying in the sort mode SORT/GROUPSet the originals face up in the document feeder tray Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display keyUse the Preset Ratio selector , keys and zoom XY ZoomReverse Dual page Copy Press the Dual page Copy keyPlace the originals on the original table with the center Rotation Copying 2 x 11 is performed, the image cannot be rotated1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selectionPress the Erase key to select the desired erase mode EraseEnsure that the desired copy paper size is selected Erase Until the Margin Shift indicator will blink Margin ShiftPlace the original in the document feeder tray or on To confirm or set the location of the margin, pressToner Cartridge Replacement Push the toner cartridge lock release lever and pullToner Cartridge Replacement Toner cartridge lifeThan 5 seconds Press the light keyMisfeed in the Rspf First confirm the misfeed locationMisfeed Removal Misfeed in the bypass trayMisfeed in the copier If the misfed original cannot be removed in steps 1Removing it Push gently on both sides of the front cover to open CoverTurn the roller rotating knob in the direction ArrowMisfeed in the upper paper tray Close the side cover by pressing the handle on CoverMisfeed in the lower paper tray Pull out the lower paper tray and remove the misfed paperClose the paper tray Close the lower side cover If the misfed paper is not seen in , gently liftMaintenance Required Developer RequiredUser Programs List of user programsProgram Program name Description Setting the user programs Enter a program number using the numeric keysUser Programs Program name Program NoTo continue with other user programs, press the key Settings for auditing accounts Select the desired setting using the numeric keysEnter a 3-digit account number using the numeric keys Number to be changed Use the copy ratio display key to select the accountUse the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Power Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode Copying from the auto power shut-off modeUser Maintenance Bypass tray with a soft, clean cloth dampened withOriginal table and document feeder cover Bypass tray paper feed rollerUser Maintenance Transfer charger cleaningCharger cleaner out by holding the tab Gently lift and pull out the upper paper tray and takeProblem Solution Copier TROUBLE?Problem Copier TROUBLE?COPY/FAX key Self-diagnostic function ExampleSupplies Types and sizes of copy paperSupplies Genuine supplies statementProper storage Store the supplies in a location that isSpecifications RspfSpecifications Reversing Single Pass FeederOptional Equipment System Configuration Part Names Loading copy paperMisfeed removal Specifications AR-DE5Index Index Material Safety Data Sheet Emergency and First Aid ProceduresProduct Routes of EntryIgnition Temperature Special Fire Fighting ProcedureSpecific Gravity Vapor Pressure Vapor DensityIngredients ProportionHealth Hazards Medical Conditions Generally Aggravated by ExposureEvaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor OdorlessMemo For users in the USA Sharp Corporation
Top Page Image Contents