Sharp AR-207 operation manual Misfeed in the Rspf, First confirm the misfeed location

Page 46

i MISFEED REMOVAL

The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location.

If paper is accidentally torn during removal, be sure to remove all pieces.

Be careful not to damage the photoconductive drum.

For misfeeds in optional equipment, see their respective sections of the operation manual.

First confirm the misfeed location.

( P.44)

( P.45, 48)

( P.49) ( P.72)

Misfeed removal

INDICATORS

STATUS

A

C

Location A

Feeding roller cover

Location B

Right side cover

Misfeed in the RSPF

If an original misfeed occurs in the RSPF, the copier will stop and the red indicator which indicates an original misfeed will blink.

B

Open the feeding roller cover and pull the original gently

1 to the left and out from the document feeder tray. Close the feeding roller cover.

If the misfed original cannot be removed in step 1, open

2 the right side cover and remove the misfed original. Close the right side cover.

44

Image 46

Contents AR-207 Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.24 Alarm indicatorsOriginal Size Enter key and indicators Start key and indicatorPreset Ratio selector keys and indicators Auto Paper Select indicatorDo not install your copier in areas that are Copier InstallationAlso make certain the outlet is properly grounded Do not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Enter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Stream feeding mode Power onTurn the power switch on Normal CopyingEnsure that the one-sided to one-sided copying mode is Adjust the copy densityNormal Copying Press the Start key Set the number of copies using the numeric keysTwo-sided copies from one-sided originals Ensure that no original is left on the original tableSet the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder trayClose the document feeder cover Ensure that the desired paper tray is selectedCopying from the Original Table Copying from the original table Select the desired parameter using the numeric keys Setting image rotation in duplex copyingPress the Original to Copy key REDUCTION/ENLARGEMENT/ZOOM AutomaticRatio, then press REDUCTION/ENLARGEMENT/ZOOMManual To increase the ratioBypass Feed special paper Unfold the bypass trayBypass Feed special paper SORT/GROUP Sort modeGroup mode Offset stackSORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display keyUse the Preset Ratio selector , keys and zoom XY ZoomReverse Press the Dual page Copy key Dual page CopyPlace the originals on the original table with the center Rotation Copying 2 x 11 is performed, the image cannot be rotated1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selectionErase Press the Erase key to select the desired erase modeEnsure that the desired copy paper size is selected Erase Place the original in the document feeder tray or on Until the Margin Shift indicator will blinkMargin Shift To confirm or set the location of the margin, pressToner Cartridge Replacement Push the toner cartridge lock release lever and pullThan 5 seconds Toner Cartridge ReplacementToner cartridge life Press the light keyMisfeed in the Rspf First confirm the misfeed locationMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray If the misfed original cannot be removed in steps 1Removing it Push gently on both sides of the front cover to open CoverTurn the roller rotating knob in the direction ArrowMisfeed in the upper paper tray Close the side cover by pressing the handle on CoverClose the paper tray Close the lower side cover Misfeed in the lower paper trayPull out the lower paper tray and remove the misfed paper If the misfed paper is not seen in , gently liftMaintenance Required Developer RequiredList of user programs User ProgramsProgram Program name Description User Programs Setting the user programsEnter a program number using the numeric keys Program name Program NoTo continue with other user programs, press the key Select the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Number to be changed Use the copy ratio display key to select the accountUse the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Copying from the preheat mode Power Save ModesSetting the power save modes Copying from the auto power shut-off modeOriginal table and document feeder cover User MaintenanceBypass tray with a soft, clean cloth dampened with Bypass tray paper feed rollerCharger cleaner out by holding the tab User MaintenanceTransfer charger cleaning Gently lift and pull out the upper paper tray and takeProblem Solution Copier TROUBLE?Copier TROUBLE? ProblemCOPY/FAX key Self-diagnostic function ExampleSupplies Types and sizes of copy paperProper storage SuppliesGenuine supplies statement Store the supplies in a location that isSpecifications RspfSpecifications Reversing Single Pass FeederOptional Equipment System Configuration Part Names Loading copy paperMisfeed removal Specifications AR-DE5Index Index Product Material Safety Data SheetEmergency and First Aid Procedures Routes of EntrySpecific Gravity Vapor Pressure Ignition TemperatureSpecial Fire Fighting Procedure Vapor DensityHealth Hazards IngredientsProportion Medical Conditions Generally Aggravated by ExposureEvaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor OdorlessMemo For users in the USA Sharp Corporation