Sharp AR-207 operation manual For users in the USA

Page 83

For users in the USA

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment gen- erates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interfer- ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

NOTICE for users in the USA

BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WAR- RANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Sharp extends a limited warranty to each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you on terms that are no less favorable than those given to the dealer by Sharp. You should be aware, however, that Sharp does not itself extend any warranties, either express or implied, directly to you, the end- user, and no one is authorized to make any representations or warranties on behalf of Sharp. Specifically, SHARP DOES NOT EXTEND TO YOU, THE END-USER,

ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED IN, OR USED IN CONJUNCTION WITH THIS PROD- UCT. Sharp is not responsible for any damages or loss, either direct, incidental or consequential, which you, the end-user, may experience as a result of your pur- chase or use of the hardware, software or firmware embodied in or used in con- junction with this Product. Your sole remedy, in the event that you encounter any difficulties with this Product, is against the authorized dealer from which you pur- chased the Product.

AR-207 Digital Laser Copier

In the event that this authorized dealer does not honor its warranty commitments, please contact the General Manager, Business Products Group, Sharp Electronics Corporation, Sharp Plaza, Mahwah, NJ 07430-2135, so that Sharp can try to help assure complete satisfaction of all the warranty rights to which you are entitled from the authorized dealer.

Page 82 Page 84
Image 83
Page 82 Page 84
Contents AR-207 Safety Precautions Contents Conventions used in this manual IntroductionMain Features Part Names and Functions Part Names and Functions Alarm indicators Interrupt key and indicator pZoom indicator p.24 Paper Size indicatorsAuto Paper Select indicator Start key and indicatorPreset Ratio selector keys and indicators Original Size Enter key and indicatorsAlso make certain the outlet is properly grounded Copier InstallationDo not install your copier in areas that are Do not touch the photoconductive drum green portion Push the paper tray firmly back into the copier Loading Copy PaperGently lift and pull out the paper tray until it stops Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Auditing Accounts When copying is completed, press the Audit Clear KeyEnter your account number using the numeric keys Normal Copying Power onTurn the power switch on Stream feeding modeNormal Copying Adjust the copy densityEnsure that the one-sided to one-sided copying mode is Ensure that no original is left on the original table Set the number of copies using the numeric keysTwo-sided copies from one-sided originals Press the Start keySet the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key Original has been set in the document feeder tray One-sided copies from two-sided originalsEnsure that the desired paper tray is selected Close the document feeder coverCopying from the Original Table Copying from the original table Press the Original to Copy key Setting image rotation in duplex copyingSelect the desired parameter using the numeric keys Automatic REDUCTION/ENLARGEMENT/ZOOMTo increase the ratio REDUCTION/ENLARGEMENT/ZOOMManual Ratio, then pressUnfold the bypass tray Bypass Feed special paperBypass Feed special paper Offset stack Sort modeGroup mode SORT/GROUPSet the originals face up in the document feeder tray Copying in the sort modeSORT/GROUP Interrupting a Copy RUN Automatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModePress the copy ratio display key XY ZoomXY Zoom Use the Preset Ratio selector , keys and zoomReverse Place the originals on the original table with the center Dual page CopyPress the Dual page Copy key 2 x 11 is performed, the image cannot be rotated Rotation Copying1 or 4 Press the 2 in 1 / 4 in 1 key to complete the selection Enter the desired pattern number using a numeric keyEnsure that the desired copy paper size is selected Press the Erase key to select the desired erase modeErase Erase To confirm or set the location of the margin, press Until the Margin Shift indicator will blinkMargin Shift Place the original in the document feeder tray or onPush the toner cartridge lock release lever and pull Toner Cartridge ReplacementPress the light key Toner Cartridge ReplacementToner cartridge life Than 5 secondsFirst confirm the misfeed location Misfeed in the RspfIf the misfed original cannot be removed in steps 1 Misfeed RemovalMisfeed in the bypass tray Misfeed in the copierPush gently on both sides of the front cover to open Cover Removing itArrow Turn the roller rotating knob in the directionClose the side cover by pressing the handle on Cover Misfeed in the upper paper trayIf the misfed paper is not seen in , gently lift Misfeed in the lower paper trayPull out the lower paper tray and remove the misfed paper Close the paper tray Close the lower side coverDeveloper Required Maintenance RequiredProgram Program name Description User ProgramsList of user programs Program name Program No Setting the user programsEnter a program number using the numeric keys User ProgramsTo continue with other user programs, press the key Enter a 3-digit account number using the numeric keys Settings for auditing accountsSelect the desired setting using the numeric keys Use the copy ratio display key to select the account Number to be changedPress and hold down the 0 key Use the copy ratio display key to select the account NumberProgram No Resetting account Auto power shut-off mode Power Save ModesPreheat mode Copying from the auto power shut-off mode Power Save ModesSetting the power save modes Copying from the preheat modeBypass tray paper feed roller User MaintenanceBypass tray with a soft, clean cloth dampened with Original table and document feeder coverGently lift and pull out the upper paper tray and take User MaintenanceTransfer charger cleaning Charger cleaner out by holding the tabCopier TROUBLE? Problem SolutionCOPY/FAX key ProblemCopier TROUBLE? Example Self-diagnostic functionTypes and sizes of copy paper SuppliesStore the supplies in a location that is SuppliesGenuine supplies statement Proper storageRspf SpecificationsReversing Single Pass Feeder SpecificationsOptional Equipment System Configuration Loading copy paper Part NamesMisfeed removal AR-DE5 SpecificationsIndex Index Routes of Entry Material Safety Data SheetEmergency and First Aid Procedures ProductVapor Density Ignition TemperatureSpecial Fire Fighting Procedure Specific Gravity Vapor PressureMedical Conditions Generally Aggravated by Exposure IngredientsProportion Health HazardsAppearance Fine powder Color Black Odor Odorless Evaporation Rate Not applicable ViscosityMemo For users in the USA Sharp Corporation
Top Page Image Contents