Sharp AR-207 operation manual Self-diagnostic function, Example

Page 66

COPIER TROUBLE?

Problem

Solution

● Is the output tray full (		) indicator		Remove the paper on or under the job separator
on and any misfeed location (			)	tray so that it can move to the proper position,
indicator	blinking	while	the	and then open and close the side cover.
misfeed (	) indicator is		not
blinking?

Power is on but copying is not possible.

Lighting fixture flickers.

●Is two-sided printing being performed?

●Is blinking in the copy quantity display?

●Is steadily lit in the copy quantity display?

●Is the indicator blinking?

●Is the indicator blinking?

●Is the same power outlet used for the lighting fixture and the copier?

Wait until the printing job will finish.

The toner cartridge is not installed. Install the toner cartridge. If "CH" is blinking even if the cartridge is installed properly, contact your SHARP service center immediately.

Side cover(s) is open.

Close the front and side covers securely.

The toner cartridge must be replaced. See page

42, TONER CARTRIDGE REPLACEMENT.

A misfeed has occurred. See page 44, MISFEED REMOVAL.

Connect the copier to a power outlet which is not used for other electric appliances.

GENERAL INFORMATION Copier trouble?

Be sure to use only genuine SHARP parts and sup- plies.

Please contact your SHARP service center immediately if a problem persists after checking the above.

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage. An alphanumeric code will appear in the copy quantity display.

Example

Should the copier completely stop and a letter and a number appear alternately, contact your SHARP service center immediately.

64

Image 66

Contents AR-207 Safety Precautions Contents Introduction Conventions used in this manualMain Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.24 Alarm indicatorsOriginal Size Enter key and indicators Start key and indicatorPreset Ratio selector keys and indicators Auto Paper Select indicatorCopier Installation Do not install your copier in areas that areAlso make certain the outlet is properly grounded Do not touch the photoconductive drum green portion Loading Copy Paper Gently lift and pull out the paper tray until it stopsPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key When copying is completed, press the Audit Clear Key Enter your account number using the numeric keysAuditing Accounts Stream feeding mode Power onTurn the power switch on Normal CopyingAdjust the copy density Ensure that the one-sided to one-sided copying mode isNormal Copying Press the Start key Set the number of copies using the numeric keysTwo-sided copies from one-sided originals Ensure that no original is left on the original tableTwo-sided copies from two-sided originals Set the number of copies and press the Start keySet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder trayClose the document feeder cover Ensure that the desired paper tray is selectedCopying from the Original Table Copying from the original table Setting image rotation in duplex copying Select the desired parameter using the numeric keysPress the Original to Copy key REDUCTION/ENLARGEMENT/ZOOM AutomaticRatio, then press REDUCTION/ENLARGEMENT/ZOOMManual To increase the ratioBypass Feed special paper Unfold the bypass trayBypass Feed special paper SORT/GROUP Sort modeGroup mode Offset stackCopying in the sort mode SORT/GROUPSet the originals face up in the document feeder tray Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyXY Zoom Press the copy ratio display keyUse the Preset Ratio selector , keys and zoom XY ZoomReverse Dual page Copy Press the Dual page Copy keyPlace the originals on the original table with the center Rotation Copying 2 x 11 is performed, the image cannot be rotated1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selectionPress the Erase key to select the desired erase mode EraseEnsure that the desired copy paper size is selected Erase Place the original in the document feeder tray or on Until the Margin Shift indicator will blinkMargin Shift To confirm or set the location of the margin, pressToner Cartridge Replacement Push the toner cartridge lock release lever and pullThan 5 seconds Toner Cartridge ReplacementToner cartridge life Press the light keyMisfeed in the Rspf First confirm the misfeed locationMisfeed in the copier Misfeed RemovalMisfeed in the bypass tray If the misfed original cannot be removed in steps 1Removing it Push gently on both sides of the front cover to open CoverTurn the roller rotating knob in the direction ArrowMisfeed in the upper paper tray Close the side cover by pressing the handle on CoverClose the paper tray Close the lower side cover Misfeed in the lower paper trayPull out the lower paper tray and remove the misfed paper If the misfed paper is not seen in , gently liftMaintenance Required Developer RequiredUser Programs List of user programsProgram Program name Description User Programs Setting the user programsEnter a program number using the numeric keys Program name Program NoTo continue with other user programs, press the key Settings for auditing accounts Select the desired setting using the numeric keysEnter a 3-digit account number using the numeric keys Number to be changed Use the copy ratio display key to select the accountUse the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Power Save Modes Preheat modeAuto power shut-off mode Copying from the preheat mode Power Save ModesSetting the power save modes Copying from the auto power shut-off modeOriginal table and document feeder cover User MaintenanceBypass tray with a soft, clean cloth dampened with Bypass tray paper feed rollerCharger cleaner out by holding the tab User MaintenanceTransfer charger cleaning Gently lift and pull out the upper paper tray and takeProblem Solution Copier TROUBLE?Problem Copier TROUBLE?COPY/FAX key Self-diagnostic function ExampleSupplies Types and sizes of copy paperProper storage SuppliesGenuine supplies statement Store the supplies in a location that isSpecifications RspfSpecifications Reversing Single Pass FeederOptional Equipment System Configuration Part Names Loading copy paperMisfeed removal Specifications AR-DE5Index Index Product Material Safety Data SheetEmergency and First Aid Procedures Routes of EntrySpecific Gravity Vapor Pressure Ignition TemperatureSpecial Fire Fighting Procedure Vapor DensityHealth Hazards IngredientsProportion Medical Conditions Generally Aggravated by ExposureEvaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor OdorlessMemo For users in the USA Sharp Corporation