Sharp XG-C465X, XG-C435X specifications Dhcp

Page 23

Setting up the Projector Network Environment

4 The TCP/IP setting screen ap- pears, ready for network settings for the projector.

Items

Setting example / Remarks

DHCP

Select “ON” or “OFF” to determine

Client

whether to use DHCP Client.

IP Address

You can set this item when “DHCP

 

Client” is set to “OFF”.

 

Factory default setting: 192.168.150.2

 

Enter an IP address appropriate

 

for the network.

Subnet

You can set this item when “DHCP

Mask

Client” is set to “OFF”.

 

Factory default setting: 255.255.255.0

 

Set the subnet mask to the same

 

as that of the computer and

 

equipment on the network.

Default

You can set this item when “DHCP

Gateway

Client” is set to “OFF”.

 

Factory default setting: 0.0.0.0

 

* When not in use, set to “0.0.0.0”.

DNS

Factory default setting: 0.0.0.0

Server

* When not in use, set to “0.0.0.0”.

Note

Confirm the existing network’s segment (IP address group) to avoid setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers. If “192.168.150.2” is not used in the network

having an IP address of “192.168.150.XXX”, you don’t have to change the projector IP address.

For details about each setting, consult your network administrator.

5

6

Click the “Apply” button.

The set values appear. Confirm that the values are set properly, and then click the “Confirm” but- ton.

Close the browser.

This completes the network settings.

After setting items, wait for 10 seconds and then re-access.

Change the IP address of the setting computer back to its original address, which you have noted down in Step 6-1on page 21, and then connect the computer and the projector to the network.

-23

Image 23
Contents Setup Manual Standard Setup Front Projection Setting up the Screen12.2 15.2m 50ft Screen Size and Projection DistanceThrow Distance ScreenF1.7-F1.9, f=28.0-33.6 mm Normal ModeStretch Mode Standard Zoom LensF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsBasic format RS-232C Specifications and CommandsComputer control Communication conditions W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsExample of the display when an error occurs Mail Recipient SettingsOccurs Service & Support Access URL Launch general purpose terminal emulator Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu Set Items View Setting Detail ListVView All Setting Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C41MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C27MZ is installed