Sharp XG-C465X, XG-C435X Confirming the Projector, Controlling the Projector, Status Status

Page 25

Confirming the Projector

Status (Status)

Controlling the Projector via LAN

Controlling the Projector

(Control)

On this screen, you can confirm the projector status. You can confirm the following items :

•MAC Address

•Power

•Condition

•Lamp Timer

•Lamp Life

•Input

•Signal Info

•Serial Number

Note

•If you click the “Refresh” button before the screen is displayed completely, an error message (“Server Busy Error”) will be dis- played. Wait for a moment and then oper- ate again.

•For details about each item, refer to the projector’s operation manual.

On this screen, you can perform projector con- trol. You can control the following items :

•Power

•Input Select

•Volume

•AV Mute

Note

•If you click the “Refresh” button before the screen is displayed completely, an error mes- sage (“Server Busy Error”) will be displayed. Wait for a moment and then operate again.

•You cannot operate this page while the pro- jector is warming up.

•While the projector is in standby mode, you can only control “Power ON”.

•For details about each item, refer to the projector’s operation manual.

-25

Image 25

Contents Setup Manual Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceScreen 12.2 15.2m 50ftStretch Mode Normal ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsComputer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralOccurs Service & Support Access URL Mail Recipient SettingsExample of the display when an error occurs When Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetInput setup and press the Enter key Launch general purpose terminal emulatorClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu VView All Setting View Setting Detail ListSet Items Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDhcp Client Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C18MZ is installed When AN-C12MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed