Sharp XG-C435X Disconnecting All Connec, Setting Auto Logout Time, Entering Advanced Setup Menu

Page 36

Setting up the Projector Using RS-232C or Telnet

Disconnecting All Connec-

tions ([D]Disconnect All)

Setting Auto Logout Time

(ADVANCED[1]Auto Logout Time)

It is possible to disconnect all the TCP/IP connec- tions currently recognized by the projector. Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection.

setup>d	1
Disconnect All Connections(y/n)?y	2
Now Disconnecting...

1Enter “d” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

Note

•If Disconnect All is performed, the connection to the projector via network will be forcibly discon- nected.

Entering ADVANCED SETUP MENU

([A]Advanced Setup)

Enters ADVANCED SETUP MENU.

setup>a	1
****************** ADVANCED SETUP MENU *********************
[1]Auto Logout Time	[2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1)	[7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr	[0]Search Port

[!]Restore Default Setting [Q]Return to Main Menu

advanced>

1 Enter “a” and press the “Enter” key.

If there is no input after a fixed time, the projector automatically disconnects network connection using the Auto Logout function. It is possible to set the time until the projector is automatically disconnected in units of a minute (from 1 to 65535 minutes).

advanced>1			1
Valid range	: 0 to 65535 (minute)
note: if you enter “0”, auto logout function will be disable.
Auto Logout Time : 5
Please Enter	:15			2

(change)	—> 15		*

1Enter “1” and press the “Enter” key.

2Enter numerical value and press the“Enter”key. Display set numerical value (*).

Note

•If the set value is made 0, the Auto Logout func- tion is disabled.

•If an invalid number is entered, an error message (“Parameter Error!”) will be displayed and the screen returns to the ADVANCED SETUP MENU.

Data Port Setting

(ADVANCED[2]Data Port)

Setting of TCP port number. It is possible to set in the range of 1025 to 65535.

advanced>2			1
Valid range	:1025 to 65535
Data Port	:10002
Please Enter	:10005			2

(change)	—> 10005		*

1Enter “2” and press the “Enter” key.

2Enter numerical value and press the“Enter”key. Display set numerical value (*).

Note

•Set according to need. Normally, use with the fac- tory default setting.

-36

Image 36

Contents Setup Manual Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceScreen 12.2 15.2m 50ftNormal Mode Stretch ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmWide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mmTele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mmTele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mmTele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mmChanging the Lens InfoReplace the lens housing cover Insert the lens into the projectorConnecting Pin Assignments COMPUTER-RGB Input/Output Component Input/OutputConnecting Pin Assignments Pin No. SignalRS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W RReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Setting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Launch general purpose terminal emulatorWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu View Setting Detail List VView All SettingSet Items Save Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDhcp Client Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Close HyperTerminalTroubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mmWhen AN-C12MZ is installed When AN-C18MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed