Sharp XG-C465X, XG-C435X specifications Resetting the Lamp Timer of the Projector via LAN

Page 39

Resetting the Lamp Timer of the Projector via LAN

When the projector is connected to a network, you can use HyperTerminal or a similar com- munications program to send a command to reset the lamp timer. The example below uses Windows® XP as the operating system.

1 Click “Start” – “All Programs” – “Accessories” – “Communica- tions” – “HyperTerminal”.

•If you do not have HyperTerminal in- stalled, see the operation manual of your computer.

•Depending on the settings of your com- puter, you may be required to enter your area code and other details. Enter the information as required.

2 Enter a name in the “Name”field, and click “OK”.

3 If you are required to enter the area code, enter it in the “Area

code” field. From the “Connect

using” drop-down menu, select

“TCP/IP (Winsock)”, and click

“OK”.

4 Enter the IP address of the pro- jector in the “Host address” field (see “TCP/IP” on the “Network” menu of the projector), and en- ter the data port of the projector in the “Port number” field (“10002” is the factory default setting), and click “OK”.

Select

“TCP/IP (Winsock)”

-39

Image 39

Contents Setup Manual Standard Setup Front Projection Setting up the Screen12.2 15.2m 50ft Screen Size and Projection DistanceThrow Distance ScreenF1.7-F1.9, f=28.0-33.6 mm Normal ModeStretch Mode Standard Zoom LensF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsRS-232C Specifications and Commands Computer control Communication conditionsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsMail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Launch general purpose terminal emulator Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu View Setting Detail List VView All SettingSet Items Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C41MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C27MZ is installed