Sharp XG-C435X, XG-C465X IP Address Setting, Default Gateway Setting, Subnet Mask Setting

Page 34

Setting up the Projector Using RS-232C or Telnet

The setting procedure for each item will be explained. For the basic procedure, please refer to “Set Items” on page 32.

IP Address Setting

([1]IP Address)

Setting of IP address.

setup>1

 

 

IP Address

 

:192.168.150.2

Please Enter

:192.168.150.3

(change)

—>

192.168.150.3

Default Gateway Setting

([3]Default Gateway)

Setting default gateway.

1

setup>3

1

 

note: “0.0.0.0” means “Using no default gateway.”

 

2Gateway Address :0.0.0.0

*

Please Enter

:192.168.150.1

 

2

 

 

(change)

—> 192.168.150.1

*

1Enter “1” and press the “Enter” key.

2Enter numerical value to be set and press the “Enter” key.

Display IP address after change (*).

1Enter “3” and press the “Enter” key.

2Enter numerical value to be set and press the “Enter” key.

Display gateway address after change (*).

Subnet Mask Setting

([2]Subnet Mask)

Setting subnet mask.

setup>2

 

 

1

Subnet Mask

:255.255.255.0

 

 

Please Enter

:255.0.0.0

 

 

2

 

 

(change) —>

255.0.0.0

 

*

1Enter “2” and press the “Enter” key.

2Enter numerical value to be set and press the “Enter” key.

Display subnet mask after change (*).

Note

If the values for IP Address, Subnet Mask or Gate- way of the projector have been changed via Telnet, the computer cannot be connected to the projector depending on the computer’s network settings.

User Name Setting

([4]User Name)

Carrying out security protection using user name.

setup>4

 

 

1

User Name

:

 

 

 

Please Enter

: XX-XXXX

 

 

2

 

 

(change)

—> XX-XXXX

*

1Enter “4” and press the “Enter” key.

2Enter user name and press the “Enter” key. Display set user name (*).

Note

User name can be up to 8 characters.

You can input the characters below : a-z, A-Z, 0-9, -, _

In the default state, user name is not set.

-34

Image 34
Contents Setup Manual Setting up the Screen Standard Setup Front ProjectionScreen Screen Size and Projection DistanceThrow Distance 12.2 15.2m 50ftStandard Zoom Lens Normal ModeStretch Mode F1.7-F1.9, f=28.0-33.6 mmWide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mmTele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mmTele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mmTele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mmChanging the Lens InfoReplace the lens housing cover Insert the lens into the projectorConnecting Pin Assignments COMPUTER-RGB Input/Output Component Input/OutputConnecting Pin Assignments Pin No. SignalComputer control Communication conditions RS-232C Specifications and CommandsBasic format Commands W RReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralOccurs Service & Support Access URL Mail Recipient SettingsExample of the display when an error occurs Input setup and press the Enter key Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Launch general purpose terminal emulatorWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu VView All Setting View Setting Detail ListSet Items SSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedSubnet Mask Setting IP Address SettingDefault Gateway Setting User Name SettingDhcp Client Setting Password SettingProjector Name Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Close HyperTerminalTroubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mmWhen AN-C27MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C41MZ is installed