Sharp XG-C435X, XG-C465X Setting of Search Port, Return to Main Menu, Return to Default Settings

Page 38

Setting up the Projector Using RS-232C or Telnet

Setting of Search Port

(ADVANCED[0]Search Port)

Sets the port number used when searching for the projector from the network.

advanced>0			1
Please Enter Port Number for Search from Computer.
Valid range	: 1025 to 65535
Search Port	: 5006
Please Enter	: 5004			2

(change)	—> 5004		*

1Enter “0” and press the “Enter” key.

2Enter numerical value and press the“Enter”key. Display set numerical value (*).

Return to Main Menu

(ADVANCED[Q]Return to Main Menu)

Returns to the main SETUP MENU.

advanced>q		1
---------------------------------	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate [7]Projector Name		[8]DHCP Client
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>

1Enter “q” and press the “Enter” key. Returns to the SETUP MENU.

Note

•Set according to need. Normally, use with the fac- tory default setting.

Return to Default Settings

(ADVANCED[!]Restore Default

Setting)

Returns all menu setting values to the default state.

advanced>!

Restore All Setting to Default(y/n)? y

— User Setting Initialized —

1

2

1Enter “!” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

Note

•If the values for IP Address, Subnet Mask or Gate- way of the projector have been returned to the default settings via Telnet, the computer cannot be connected to the projector depending on the computer’s network settings.

-38

Image 38

Contents Setup Manual Setting up the Screen Standard Setup Front ProjectionScreen Screen Size and Projection DistanceThrow Distance 12.2 15.2m 50ftStandard Zoom Lens Normal ModeStretch Mode F1.7-F1.9, f=28.0-33.6 mmWide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mmTele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mmTele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mmTele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mmChanging the Lens InfoReplace the lens housing cover Insert the lens into the projectorConnecting Pin Assignments COMPUTER-RGB Input/Output Component Input/OutputConnecting Pin Assignments Pin No. SignalBasic format RS-232C Specifications and CommandsComputer control Communication conditions Commands W RReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralExample of the display when an error occurs Mail Recipient SettingsOccurs Service & Support Access URL Input setup and press the Enter key Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Launch general purpose terminal emulatorWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu Set Items View Setting Detail ListVView All Setting SSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedSubnet Mask Setting IP Address SettingDefault Gateway Setting User Name SettingDhcp Client Setting Password SettingProjector Name Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Close HyperTerminalTroubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mmWhen AN-C27MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C41MZ is installed