Sharp XG-C465X, XG-C435X specifications Connecting the Pro- jector to a Computer

Page 19

Setting up the Projector Network Environment

1.Connecting the Pro- jector to a Computer

Establishing a one-to-one connection from the projector to a computer. Using a LAN cable (Category 5, cross-over type) you can config- ure the projector via the computer.

1 Disconnect the computer’s LAN cable from the existing network.

A LAN cable being connected to the network

2 Connect a LAN cable (a UTP cable, Category 5, cross-over type) to the projector’s LAN ter- minal and connect the other end of the cable to the computer’s LAN terminal.

LAN cable

(cross-over type, commercially available)

3 Plug the power cord into the AC socket of the projector.

4 Turn on the computer.

ON

Info

Confirm that the LINK LED on the rear of the projector illuminates. If the LINK LED does not illuminate, check the following :

•The LAN cable is properly connected.

•The power switches of both the projector and the computer are on.

This completes the connection. Now proceed to “2. Setting an IP Address for the Com- puter”.

-19

Image 19

Contents Setup Manual Standard Setup Front Projection Setting up the Screen12.2 15.2m 50ft Screen Size and Projection DistanceThrow Distance ScreenF1.7-F1.9, f=28.0-33.6 mm Normal ModeStretch Mode Standard Zoom LensF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsComputer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsOccurs Service & Support Access URL Mail Recipient SettingsExample of the display when an error occurs Launch general purpose terminal emulator Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu VView All Setting View Setting Detail ListSet Items Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C41MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C27MZ is installed