Sharp XG-C465X, XG-C435X Troubleshooting, When connecting the projector using serial-connection

Page 41

Troubleshooting

Communication cannot be established with the projector

When connecting the projector using serial-connection

\Check that the RS-232C terminal of the projector and a computer or the commercially available controller are connected correctly.

\Check that the RS-232C cable is a cross-over cable.

\Check that the RS-232C port setting for the projector corresponds to the setting for the computer or the commercially available controller.

When connecting the projector to a computer using network (LAN)- connection

\Check that the cable’s connector is firmly inserted in the LAN terminal of the projector.

\Check that the cable is firmly inserted into a LAN port for a computer or a network device such as a hub.

\Check that the LAN cable is a Category 5 cable.

\Check that the LAN cable is a cross-over cable when connecting the projector to a computer directly.

\Check that the LAN cable is a straight-through cable when connecting the projector with a network device such as a hub.

\Check that the power supply is turned on for the network device such as a hub between the projector and a computer.

Check the network settings for the computer and the projector

\Check the following network settings for the projector.

IP Address

Check that the IP address for the projector is not duplicated on the network.

Subnet Mask

When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same:

The subnet masks for the projector and the computer should be the same.

The IP address parts shown by the subnet mask for the projector and the computer should be the same.

(Example)

When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the subnet mask should be “255.255.255.0”.

Gateway

When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same:

The subnets for the projector and the computer should be the same.

The IP address parts shown by the subnet mask for the projector and the computer should be the same.

(Example)

When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the subnet mask should be “255.255.255.0”.

Note

The factory default settings for the projector are as follows: DHCP Client : Off

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Gateway address : 0.0.0.0 (Not Used)

For network settings for the projector, refer to page 22.

-41

Image 41
Contents Setup Manual Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceScreen 12.2 15.2m 50ftStretch Mode Normal ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsBasic format RS-232C Specifications and CommandsComputer control Communication conditions W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralExample of the display when an error occurs Mail Recipient SettingsOccurs Service & Support Access URL When Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetInput setup and press the Enter key Launch general purpose terminal emulatorClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu Set Items View Setting Detail ListVView All Setting Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDhcp Client Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C18MZ is installed When AN-C12MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed