Sharp XG-C465X When AN-C12MZ is installed, When AN-C18MZ is installed, When AN-C27MZ is installed

Page 45

Dimensions

Projector and Lens Dimensions

[When AN-C12MZ is installed]

Unit : inches (mm)

15 21/64 - 15 13/32 (389 - 391)

107

[When AN-C18MZ is installed]

Unit : inches (mm)

12 3/32 - 12 11/64 (307 - 309)

67.5

[When AN-C27MZ is installed]

Unit : inches (mm)

13 7/16 - 13 5/8 (341 - 346)

80

[When AN-C41MZ is installed]

Unit : inches (mm)

13 19/32 - 13 3/4 (345 - 349)

80

-45

Image 45

Contents Setup Manual Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceScreen 12.2 15.2m 50ftStretch Mode Normal ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsRS-232C Specifications and Commands Computer control Communication conditionsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralMail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs When Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetInput setup and press the Enter key Launch general purpose terminal emulatorClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu View Setting Detail List VView All SettingSet Items Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDhcp Client Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C18MZ is installed When AN-C12MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed