Sharp XG-C465X Making General Settings for the Network Network, Mail Originator Settings

Page 27

Making General Settings for the Network (Network -

General)

Controlling the Projector via LAN

Setting for Sending E-mail when an Error Occurs

(Mail – Originator Settings)

On this screen, you can make general settings relating to the network.

Items

Description

Projector

Setting the projector name.

Name

 

Auto

Setting the time interval in

Logout

which the projector will be

Time

automatically disconnected

 

from the network in units of a

 

minute (from 1 to 65535

 

minutes). If the set value is

 

made 0, the Auto Logout

 

function is disabled.

 

 

Data Port

Setting the TCP port number

 

used when exchanging data

 

with the projector (from 1025 to

 

65535).

Search

Setting the port number used

Port

when searching for the

 

projector (from 1025 to 65535).

After clicking the “Apply” button, the set val- ues appear. Confirm that the values are set properly, and then click the “Confirm” button.

Note

After setting items, wait for 10 seconds and then re-access.

Projector Name can be up to 12 characters.

You can input the characters below : A-Z, 0-9, -, _, (,), space

(When “a-z” are input, they are converted to “A-Z” automatically.)

On this screen, you can make settings for sending e-mail to report when the projector has generated an error.

Items

Setting example / Remarks

SMTP

Setting an SMTP server

Server

address for e-mail transmis-

 

sion.

 

e.g.1 : 192.168.150.253

 

e.g.2 : smtp123.sharp.co.jp

 

* When using a domain name,

 

make settings for the DNS

 

server.

 

 

Originator

Setting the projector’s e-mail

E-mail

address. The e-mail address set

Address

here becomes Originator E-mail

 

Address.

Originator

Setting the sender’s name.

Name

The name set here appears in

 

the “Originator Name” column

 

of the body of the message.

Note

SMTP Server, Originator E-mail Address and Originator Name can be up to 64 characters.

You can input the characters below:

SMTP Server and Originator E-mail Address :

a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, , }, ~, _, ’, ., @, `

(You can input “@” only one time for “Origi- nator E-mail Address”.)

Originator Name : a-z, A-Z, 0-9, -, _, (,), space

If the settings of “3. Setting up a Network Connection for the Projector” on pages 22 and 23 are incorrectly set, e-mail will not be send.

-27

Image 27
Contents Setup Manual Standard Setup Front Projection Setting up the Screen12.2 15.2m 50ft Screen Size and Projection DistanceThrow Distance ScreenF1.7-F1.9, f=28.0-33.6 mm Normal ModeStretch Mode Standard Zoom LensF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsRS-232C Specifications and Commands Computer control Communication conditionsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsMail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Launch general purpose terminal emulator Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu View Setting Detail List VView All SettingSet Items Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C41MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C27MZ is installed