Sharp XG-C465X, XG-C435X Password Setting, Projector Name Setting, RS-232C Baud Rate Set

Page 35

Setting up the Projector Using RS-232C or Telnet

Password Setting

([5]Password)

Carrying out security protection using password.

setup>5			1
Password	:
Please Enter	: sharppj			2

(change)	—> sharppj		*

1Enter “5” and press the “Enter” key.

2Enter password and press the “Enter” key. Display set password (*).

Projector Name Setting

([7]Projector Name)

It is possible to assign a projector name.

setup>7
Projector Name	: XX-XXXX
Please Enter	: MY XX-XXXX
(change) —>	MY XX-XXXX

1Enter “7” and press the “Enter” key.

2 Enter projector name. Display set projector name (*).

1

2

*

Note

•Password can be up to 8 characters.

•You can input the characters below : a-z, A-Z, 0-9, -, _

•In the default state, the password is not set.

RS-232C Baud Rate Set-

ting ([6]RS-232C Baud Rate)

Setting of baud rate for RS-232C terminals.

setup>6				1
0	...	9600 bps
1	...	38400 bps
2	... 115200 bps
Baud Rate Select[0-2] :2					2

RS-232C Baud Rate : 115200 bps				*

1Enter “6” and press the “Enter” key.

2Select and enter the number 0, 1 or 2 and press the “Enter” key.

Display set baud rate (*).

Note

•Set the projector’s baud rate to the same rate as that used by the computer.

Note

•Projector name can be up to 12 characters.

•You can input the characters below : A-Z, 0-9, -, _, (,), space

(When “a-z” are input, they are converted to “A-Z” automatically.)

•It is the same as the name which can be con- firmed or set, using RS-232C commands “PJN0”, “PJN1”, “PJN2” and “PJN3”.

DHCP Client Setting

([8]DHCP Client)

Setting DHCP Client to “Enable” or “Disable”.

Example: When setting DHCP Client to “Enable”

setup>8	1
note: It sets DHCP Client.

0 ...	Disable
1 ...	Enable
DHCP Select[0-1] : 1					2

DHCP Client : Enabled
Success get data from DHCP server.
[MAC Address		] : [XX:XX:XX:XX:XX:XX]
[IP Address		] : [192.168.150.2]		*
[Subnet Mask		] : [255.255.255.0]
[Default Gateway		] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]

1Enter “8” and press the “Enter” key.

2 Enter “1” and press the “Enter” key. Display the obtained values (*).

-35

Image 35

Contents Setup Manual Standard Setup Front Projection Setting up the Screen12.2 15.2m 50ft Screen Size and Projection DistanceThrow Distance ScreenF1.7-F1.9, f=28.0-33.6 mm Normal ModeStretch Mode Standard Zoom LensF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsBasic format RS-232C Specifications and CommandsComputer control Communication conditions W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsExample of the display when an error occurs Mail Recipient SettingsOccurs Service & Support Access URL Launch general purpose terminal emulator Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu Set Items View Setting Detail ListVView All Setting Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C41MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C27MZ is installed