Sharp XG-C465X RS-232C Specifications and Commands, Computer control Communication conditions

Page 13

RS-232C Specifications and Commands

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard.

Parity bit: None

Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps

Stop bit: 1 bit

Data length: 8 bits

Flow control: None

*Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.

Command format

C1 C2 C3 C4 P1 P2 P3 P4

Return code (0DH)

Command 4-digit

Parameter 4-digit

Response code format Normal response

O K

Return code (0DH)

Problem response (communication error or incorrect command)

E

R

R

 

Return code (0DH)

 

 

 

 

 

Info

•When controlling the projector using RS-232C commands from a computer, wait for at least 40 seconds after the power has been turned on, and then transmit the commands.

•After sending an input selection or picture adjustment command and then receiving an “OK” response code, the projector may take some time to process the command. If a second command is sent while the projector is still processing the first command, you may receive an “ERR” response code. If this happens, try resending the second command.

•When more than one code is being sent, send each command only after the response code for the previ- ous command from the projector is verified.

•“POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”

−When the projector receives the special commands shown above:

*The on-screen display will not disappear.

*The “Auto Power Off” timer will not be reset.

−The special commands are available for applications that require continuous polling.

Note

•If an underbar (_) appears in the parameter column, enter a space.

•If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under Control Contents.

*1 Serial No. Check command is used to read out the 12 digits of serial No..

*2 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. *3 Parameters of CLR Temp settings are as follows.

CLR Temp

Parameter

CLR Temp

Parameter

5500K

_0 5 5

8500K

_0 8 5

6500K

_0 6 5

9300K

_0 9 3

7500K

_0 7 5

10500K

_1 0 5

*4 The adjustable range of “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.

-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Setup Manual Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceScreen 12.2 15.2m 50ftStretch Mode Normal ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsComputer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralOccurs Service & Support Access URL Mail Recipient SettingsExample of the display when an error occurs When Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetInput setup and press the Enter key Launch general purpose terminal emulatorClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu VView All Setting View Setting Detail ListSet Items Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDhcp Client Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C18MZ is installed When AN-C12MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed
Top Page Image Contents