Sharp XG-C465X, XG-C435X Carrying out Network Ping Test, Setting of Accept IP Ad- dress

Page 37
(ADVANCED[6]Accept IP

Setting up the Projector Using RS-232C or Telnet

Carrying out Network Ping Test

(ADVANCED[5]Network Ping Test)

It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally.

advanced>5

 

 

 

 

1

Ping dest IP addr

:192.168.150.1

 

 

 

 

Please Enter

 

:192.168.150.152

 

 

 

2

 

 

 

(change)

—>

192.168.150.152

 

 

 

*1

 

 

 

32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms

 

 

32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms

*2

32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms

 

 

32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms

 

 

 

 

 

 

 

 

 

1Enter “5” and press the “Enter” key.

2Enter IP address of device to be tested and press the “Enter” key.

Display entered IP address (*1). Display test result (*2).

Note

•If the “Enter” key is pressed without entering an IP address, the Ping destination IP address used previously is entered.

•If there is a fault with the connection, “Error: No answer” is displayed after a 5 second retry. In this case, please confirm the settings for the projector and the computer, and contact your network ad- ministrator.

Setting of Accept IP Ad- dress

Addr(1) - [8]Accept IP Addr(3))

It is possible to improve security of the projector by allowing connection from only a prescribed IP ad- dress. It is possible to set up to three IP addresses allowing connection to the projector.

advanced>6

 

 

 

1

Accept IP Addr(1)

: 0.0.0.0

 

 

 

Please Enter

 

: 192.168.150.152

 

 

2

 

 

 

(change)

—>

192.168.150.152

 

*

1Enter “6”, “7” or “8” and press the “Enter” key.

2 Enter numerical value and press the“Enter”key. Display set numerical value (*).

Note

•To invalidate the Accept IP Address being cur- rently set, enter “0.0.0.0”.

•If there is one or more Accept IP Addr being set, no connections are allowed from IP addresses that are not yet set. They can be cancelled using [9]Accept All IP Addr.

Accepting All IP Addresses

(ADVANCED[9]Accept All IP Addr)

Removes IP addresses set with “Accept IP Addr”.

advanced>9

1

Accept All IP Addresses(y/n)? y

2

 

 

1Enter “9” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

Note

•At the point in time where “y” was entered, the numerical values for Accept IP Addr(1)-(3) are reset to “0.0.0.0”.

•If “n” is entered, setting is not altered.

-37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Setup Manual Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceScreen 12.2 15.2m 50ftStretch Mode Normal ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmF2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZF1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZF2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZF2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZInfo Changing the LensInsert the lens into the projector Replace the lens housing coverCOMPUTER-RGB Input/Output Component Input/Output Connecting Pin AssignmentsPin No. Signal Connecting Pin AssignmentsComputer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralOccurs Service & Support Access URL Mail Recipient SettingsExample of the display when an error occurs When Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetInput setup and press the Enter key Launch general purpose terminal emulatorClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetSetup Menu Main Menu VView All Setting View Setting Detail ListSet Items Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name SettingProjector Name Setting Password SettingDhcp Client Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AN-C18MZ is installed When AN-C12MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed
Top Page Image Contents