TANDBERG D50104-15 user manual VNC Settings, Address, Display Number, Password, Start using VNC

Page 71

Health Care System III

Advanced Use

VNC Settings

NOTE

VNC SERVER SOFTWARE SETUP

BOTH THE PC AND THE VIDEOCONFERENCING SYSTEM MUST BE CONNECTED TO THE LAN.

A VNC SERVER MUST BE INSTALLED ON THE PC. FREE SOFTWARE CAN BE DOWNLOADED FROM HTTP://WWW.UK.RESEARCH.ATT.COM/VNC

INSTALL THE SOFTWARE BY RUNNING THE DOWNLOADED FILE.

TO CONFIGURE THE VNC SERVER SOFTWARE :

SELECT “ACCEPT SOCKET CONNECTIONS”.

SELECT “AUTOFOR “DISPLAY NUMBER”. ‘DISPLAY NUMBERIN THE SYSTEM MUST THEN HAVE THE VALUE 0.

ENTER A PASSWORD IN THE “PASSWORD”-FIELD. MUST CORRESPOND WITH THE ‘VNC SETTINGSON YOUR SYSTEM.

Address

The IP-address of the PC with the VNC software installed. To find the IP-address of the PC, select ‘Command Prompt’ from the Startup-menu. Type ‘ipconfig’ and press ENTER.

Display Number

The display number for VNC is 0 and upwards. If you are using WinVNC, double-click on the icon on the toolbar to view ‘WinVNC properties’. This number should correspond with ‘Display Number’ in this menu.

Password

Enter the same password as specified in WinVNC properties. The password will be shown as asterisk signs

(*) the next time you enter the menu.

Start using VNC

To activate VNC, press ‘PC’ on the remote control. Please make sure that ‘PC’ is set to ‘VNC’ in the ‘Video Settings Menu’. See also ‘PC SoftPresenter’ section for further information.

71

Image 71
Contents Health Care System Declaration of Conformity Copyright 2001, Tandberg For the customers in the USA Symbols Location This Symbol IndicatesOn Installation PrecautionsOn Safety On Storage On CleaningOn Repacking On MobilityContents Getting Started Advanced use Rsvp NAT 100 TIP IntroductionAt a Glance The HCS III System Monitor Main HCS III CartCamera MicrophoneCart Keyboard and Mouse customer suppliedNetwork Terminating Units Remote ControlHeadset and Jack Rear Interface PanelMobile Camera Cart optional Height Adjustable Camera ArmIntroduction Health Care System Unpacking InstallationInstallation Health Care System Connecting the SystemHealth Care System Installation To connect a video cassette recorder VCR VCRDual LAN Cable Isdn BRI CablesNET 1 External Network Interface PRI InterfaceMicrophone 3 MIC Installing a PCMain HCS III Cart Microphone Ancillary Equipment Monitor Suspension Arm Adjustment Cart AdjustmentsTriple-pivot Arm Counterbalance Adjustment Background Brightness Control Loudspeaker VolumeOperational Considerations Iris Control and LightingLighting Guidelines for setting up videoconferencing roomsWelcome menu Getting StartedSystem start-up Quick Keys BasicsMain Menu Menu StructureMenu System configurationLAN configuration Isdn configurationMaking a call Making and ending callsType of calls Selecting / setting default quality bandwidthCorrecting keying mistakes Selecting / setting default networkAnswer a call End a callDirectory Edit Entry Add New EntryDelete Entry Add Site Add MultiSite EntryView outgoing video selfview Adjusting volumeDo Not Disturb / Sleep Mode General useMoving / zooming camera Focusing cameraControlling the Main Camera Selecting video sourcesDeactivating SetupVoice Activated Camera Positioning ActivatingFar end camera control Fecc PresetsSelecting presets Storing presetsReceiving a still image Sending/receiving still imagesSending a still image Viewing a still imageAdd Duo Video Duo VideoEnd a Duo Video call MultiSite MCU MultiSite cascading Establishing MultiSite meetings using DirectoryPress ‘Add Site’ to bring up the MultiSite dial menu Adding an extra site dial outAdding an extra site dial Disconnecting sites from a conferencePC SoftPresenter PC PresenterText Chat / Closed Captioning Web-interfaceStreaming Other PC applicationsMain menu Advanced useVideo VGA ResolutionsCall quality AudioAdvanced call quality Presentations Utilities MCU status line Welcome MenuContinuous Presence System Name MCU servicesTerminal Names Quick MenuRequest floor Release floorChair control Audio Inputs Audio SettingsMix Mode Audio Outputs Level SettingsNoise Reduction Level Settings OutputsEcho Control Motion Automatic Gain Control AGC SettingsRoom Size Alert Speaker Tips for improving the echo canceller performanceAlert Tones & Volume Restore Audio DefaultsVideo Settings VGA Out Quality VGA SettingsVideo Name VGA OutAddress VNC SettingsPassword Start using VNCNetwork Configuration Terminal SettingsIsdn Switch Type ISDN-BRI SettingsLine Setup Subaddress Advanced Isdn settingsNumber ISDN-PRI SettingsPRI Switch Type Channel Hunting Below is a list of common ISDN-PRI/T1 switchesAdvanced ISDN-PRI Settings Line SettingsExternal network settings Leased E1/T1 SettingsNetwork clocking Call controlStreaming Source LAN SettingsAddress Port TTL/Router HopsSettings Register Advanced H.323 SettingsIP Type of Service TOS PrefixIP-address IP SettingsNAT Address IP-assignmentRestart Snmp SettingsIncoming telephone calls Call SettingsAccess Code Incoming MCU callsNetwork Profiles EncryptionMax Call Length Dataport Dataport configurationDataport LanguageSoftware Options Channel status DiagnosticsSystem info Call status Restore defaultsSystem Selftest View current settingsTest subsystem Far End Loop Isdn onlyAppendix Connecting the HCS III to Isdn using Network AdaptersConnecting ConfiguringConfiguration of the system Connecting the system to the Switched 56 networkUsing Telesync TS-256 SW56/ISDN adapter Configuration of Telesync AdapterConnecting to Adtran T1 ESF CSU ACE Connecting the system to PRI/T1Using CSU adapter Configuration of Adtran T1 ESF CSU ACE Environmental considerations Description of the different files Using the file systemB2 ABC Appendix 6 Access CodeTechnical Description 101 102 Abbreviations Index Symbols105 USA Servicing