Runco CL-610 Intake Vent Front IR Sensor Projection Lens, Rear/Side/Bottom View, Connector Panel

Page 18

Controls and Functions

6.INTAKE VENT

7.FRONT IR SENSOR

8.PROJECTION LENS

Rear/Side/Bottom View ➤

Figure 2-2. CL-610 Rear/Bottom/Side View

1.CONNECTOR PANEL

Refer to CL-610 Connector Panel on page 8 for more information.

2.AC POWER INPUT (100 to 240 VAC) Connect the CL-610 to power here.

3.AC POWER SWITCH

Disconnects or applies power to the CL-610.

4.CABLE ACCESS DOOR Open to access connectors.

5.CABLE OPENING

Pass cables through this opening.

6	Runco CL-610 Series Owner’s Operating Manual

Image 18

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting OperationCL-610 Table of Contents List of Figures List of Figures Xii About This Manual Carriage return must be used after each command or stringIntroduction Target AudienceSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions CL-610 at a GlanceFront/Side/Top View Intake Vent Front IR Sensor Projection Lens Connector PanelAC Power Switch Rear/Side/Bottom ViewStatus Indicators Lens ControlsLamp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Temp LEDVideo Composite Video InputRS-232 Control Port CL-610 Remote Control LightOn / OFF Hdmi VIDRgbhd InfoISF DAY MEM1ISF Night FactInstallation Remote ControlQuick Setup Installation specialistStep Procedure For Details, Refer to Installation Considerations Installation TypeAmbient Light Lens Throw Range Throw Ratio Inches, withProjector Model ScreenVertical and Horizontal PositionFolded Optics Mounting the CL-610 Connector Panel Access Connecting Source Components to the CL-610Connections to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller ConnectionConnecting 12-volt Trigger Output to ExternalTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic LensTip Selecting Video Memory Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus RGB-HD ISFPicture Adjustment Main MenuEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toYou must enter a passcode in order to enter the Set Up menu International Color Consortium ICC is a group of imagingAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view To exit InstallationTakes effect immediately you do not need to press Enter OptionShift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Order to change the secondary IR code Operation Reset Picture Adjust ISF CalibrationThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Serial Communications Is turned on or offCode Function Serial Communications Serial Commands Serial Communications Specifications CL-610 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual