Runco CL-610 Connector Panel, Lamp LED, POWER/STANDBY LED Indicates power status as follows

Page 20

Controls and Functions

2.3

CL-610 Connector Panel

3.LAMP LED

Indicates lamp status as follows:

•Off during normal operation

•Red when the lamp has exceeded its usage life or developed a problem

•Flashes red when the fans are not working or the lamp cover is open

4.POWER/STANDBY LED Indicates power status as follows:

•Orange when the projector is in standby mode

•Flashes orange for 45 seconds after the projector is turned on to indicate that the lamp is warming up

•Green during normal operation

•Flashes green for 110 seconds after the projector is turned off to indicate that the lamp is cooling down

5.TEMP LED

Indicates fan status and internal temperature as follows:

•Off during normal operation

•Red when internal temperature is too high

•Flashes red when the fans are not working or the lamp cover is open

Figure 2-4shows the CL-610 connector panel.

Figure 2-4. CL-610 Connector Panel

8	Runco CL-610 Series Owner’s Operating Manual

Image 20

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting OperationCL-610 Table of Contents List of Figures List of Figures Xii Carriage return must be used after each command or string IntroductionAbout This Manual Target AudienceUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Front/Side/Top View Controls and FunctionsCL-610 at a Glance Connector Panel AC Power SwitchIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewStatus Indicators Lens ControlsCL-610 Connector Panel POWER/STANDBY LED Indicates power status as followsLamp LED Temp LEDRS-232 Control Port VideoComposite Video Input On / OFF CL-610 Remote ControlLight VID RgbhdHdmi InfoMEM1 ISF NightISF DAY FactInstallation Remote ControlStep Procedure For Details, Refer to Quick SetupInstallation specialist Ambient Light Installation ConsiderationsInstallation Type Throw Range Throw Ratio Inches, with Projector ModelLens ScreenFolded Optics Vertical and HorizontalPosition Mounting the CL-610 Connections to the CL-610 Connector Panel AccessConnecting Source Components to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller ConnectionTheater Equipment Connecting 12-voltTrigger Output to External Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic LensTip Using Picture-In-Picture and Picture-By-Picture PIP/PBP OperationSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus RGB-HD ISFEnter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toAspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Installation Takes effect immediately you do not need to press EnterTo exit OptionShift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Order to change the secondary IR code Operation This menu should be used by ISF-certified technicians only Reset Picture AdjustISF Calibration When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications Specifications CL-610 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual