Runco CL-610 manual Zoom and Focus Adjustments

Page 37

Installation

1.Turn on your source components.

2.Turn on the main power switch at the rear of the projector. The POWER LED lights orange. The LAMP and TEMP LEDs light red briefly, then go out.

3.Press the ON button on the remote control to turn on the CL-610. The POWER LED flashes orange

			LIGHT
		to indicate that it is warming up.				OFF
						OFF
	4.	When the projector is ready for use, the POWER

				S-VID		COMP1 COMP2
			VID	S-VID		COMP1 COMP2
		LED lights green.
	5.	“Searching...” appears on the screen before the		RGBHD		HDMI
		CL-610 identifies the input signal and remains there
		CL-610 identifies the input signal and remains there
		until a valid signal is detected.

6.If an incompatible input signal exceeds the range of the projector, a “No signal supported” message appears on the screen. This message remains on the screen until you change the input signal.

The CL-610 OSD language is initially set to English, but can also display the menus in French, Spanish, Italian or German. To change the OSD language:

1.Press MENU.

2.Select Installation from the Main Menu and press ENTER.

3.Select Language from the Installation Menu and press ENTER.

4.Press or to highlight the desired language. (The change takes effect immediately.)

By default, the CL-610 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this:

1.Press MENU on the remote control.

2.Select Installation from the Main Menu and press ENTER.

3.Select Picture Orientation from the Installation Menu and press ENTER.

4.Choose Floor Rear, Ceiling Front or Ceiling Rear to match the installation method.

3.6

Turning On the Power

3.7

Changing the OSD Language

3.8

Adjusting the Picture Orientation

The CL-610 gives you a great deal of control over the picture size and focus.

Adjust the projected image size with
the zoom ring on the lens. To focus
the image, rotate the focus ring on
the lens.	Focus
	Focus
Zoom out	Zoom in

3.9

Zoom and Focus Adjustments

Runco CL-610 Series Owner’s Operating Manual

25

Image 37

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories CL-610 at a Glance Controls and FunctionsFront/Side/Top View AC Power Switch Connector PanelIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewLens Controls Status IndicatorsPOWER/STANDBY LED Indicates power status as follows CL-610 Connector PanelLamp LED Temp LEDComposite Video Input VideoRS-232 Control Port Light CL-610 Remote ControlOn / OFF Rgbhd VIDHdmi InfoISF Night MEM1ISF DAY FactRemote Control InstallationInstallation specialist Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsAmbient Light Projector Model Throw Range Throw Ratio Inches, withLens ScreenPosition Vertical and HorizontalFolded Optics Mounting the CL-610 Connecting Source Components to the CL-610 Connector Panel AccessConnections to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerTrigger Output to External Connecting 12-voltTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Operation Using Picture-In-Picture and Picture-By-Picture PIP/PBPSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus ISF RGB-HDMain Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Takes effect immediately you do not need to press Enter InstallationTo exit OptionShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation ISF Calibration Reset Picture AdjustThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual