Runco CL-610 manual Maintenance and Troubleshooting, Lamp Replacement

Page 61

Maintenance and Troubleshooting

The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to obtain a replacement lamp.

1. Turn off the projector and unplug the power cord.

Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement.

2.Remove the two screws from the lamp cover.

3.Remove the lamp cover.

4. Remove the two lamp assembly mounting screws.

5.Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing.

6. Install the new lamp module and replace the two screws you removed in Step 4.

5.1

Lamp Replacement

7.Replace the lamp cover at the top first and secure it with the two screws you removed in Step 2.

8.Turn on the power and select Reset Lamp Timer from the Set Up menu to reset the lamp timer (refer to Reset Lamp Timer on page 45).

Runco CL-610 Series Owner’s Operating Manual

49

Image 61
Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories CL-610 at a Glance Controls and FunctionsFront/Side/Top View AC Power Switch Connector PanelIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewLens Controls Status IndicatorsPOWER/STANDBY LED Indicates power status as follows CL-610 Connector PanelLamp LED Temp LEDComposite Video Input VideoRS-232 Control Port Light CL-610 Remote ControlOn / OFF Rgbhd VIDHdmi InfoISF Night MEM1ISF DAY FactRemote Control InstallationInstallation specialist Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsAmbient Light Projector Model Throw Range Throw Ratio Inches, withLens ScreenPosition Vertical and HorizontalFolded Optics Mounting the CL-610 Connecting Source Components to the CL-610 Connector Panel AccessConnections to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerTrigger Output to External Connecting 12-voltTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Operation Using Picture-In-Picture and Picture-By-Picture PIP/PBPSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus ISF RGB-HDMain Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Takes effect immediately you do not need to press Enter InstallationTo exit OptionShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation ISF Calibration Reset Picture AdjustThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual